INSTALLATION
Removal / installation · Vehicles built Aug 2012 – Jul 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
| 1. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install the front pipe to the pipe support.
Install a new gasket and the front pipe to the exhaust manifold.
Install the front pipe with the 2 nuts.
- Torque:
- 62 N*m{ 632 kgf*cm , 46 ft.*lbf }
| 2. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY |
Install the front pipe to the pipe support.
Install 2 new gaskets and the front pipe to the exhaust manifold.
Install the front pipe with the 2 bolts and 2 nuts.
- Torque:
- 62 N*m{ 632 kgf*cm , 46 ft.*lbf } for nut
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf } for bolt
- NOTICE:
- Do not reuse the gasket.
| 3. INSTALL CENTER EXHAUST PIPE ASSEMBLY |
Using a vernier caliper, measure the free length of the compression spring.

- Minimum length:
- 40.5 mm (1.5945 in.)
Install the center pipe to the 3 pipe supports.
Install a new gasket to the front exhaust pipe.
- HINT:
- Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and front exhaust pipe fit properly.
- NOTICE:
-
Be careful with the installation direction of the gasket.

-
- Do not reuse the gasket.
- Do not reuse the gasket.
- To ensure a proper seal, do not use the tailpipe to force the gasket onto the front exhaust pipe.
- To ensure a proper seal, do not use the tailpipe to force the gasket onto the front exhaust pipe.
Install the exhaust pipe with the 2 bolts and 2 springs.
- Torque:
- 43 N*m{ 438 kgf*cm , 32 ft.*lbf }
| 4. INSTALL TAILPIPE ASSEMBLY |
Install a new gasket on the center exhaust pipe.
Install the tailpipe with the 2 bolts.
- Torque:
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf }
- NOTICE:
- Do not reuse the gasket.
| 5. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2) |
![]() ![]() |
Using SST, install the sensor to the front exhaust pipe.
- SST
- 09224-00010
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST
- HINT:
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
Connect the sensor connector.
| 6. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2) |
![]() ![]() |
Using SST, install the sensor to the front exhaust pipe.
- SST
- 09224-00010
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST
- HINT:
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
Connect the sensor connector.
| 7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 8. CHECK FOR EXHAUST GAS LEAKS |
| 9. PERFORM INITIALIZATION |
Perform initialization (Click here).
- NOTICE:
- Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.


