2014 Hilux · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011

HINT:
  1. Thoroughly clean all parts to be assembled.
  2. Before installing the parts, apply new engine oil to all sliding and rotating surfaces.
  3. Replace all gaskets, O-rings and oil seals with new parts.


1. REMOVE CYLINDER HEAD
  1. Remove the cylinder head (Click here).


2. REMOVE CYLINDER HEAD GASKET
  1. Remove the cylinder head gasket from the cylinder head.


3. REMOVE GENERATOR WITH VACUUM PUMP ASSEMBLY

A118424
  1. Disconnect the terminal cap.

  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. A118425
    Remove the union bolt to disconnect the vacuum pump hose and remove the 2 gaskets.

  1. Remove the union bolt to disconnect the vacuum pump oil inlet hose and remove the 2 gaskets.

  1. Detach the vacuum pump oil inlet hose from the cord clip.

  1. Disconnect the vacuum pump oil outlet hose.

  1. A122287
    Remove the bolt and generator.


4. REMOVE INJECTION PUMP DRIVE PULLEY

  1. A071313E01
    Using SST, remove the pulley nut.
    SST
    09213-14010   (91651-60865)
    09330-00021  

  1. A071314E01
    Using SST, remove the drive pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


5. REMOVE INJECTION PUMP ASSEMBLY

  1. A121086E01
    Disconnect the engine speed sensor connector.

  1. Disconnect the spill control valve connector.

  1. Disconnect the correction unit connector.

  1. Disconnect the timing control valve connector.

  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the engine wire clamp.

  1. Disconnect the 3 fuel hoses.

  1. A071318E01
    Remove the 3 bolts and injection pump stay.

  1. Remove the 2 nuts and injection pump.


6. REMOVE OIL FILTER

  1. A118167E01
    Using SST, remove the oil filter.
    SST
    09228-44011  


7. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. A118122
    Remove the 10 bolts, 2 nuts, oil filter bracket and gasket.


8. REMOVE ENGINE OIL PRESSURE SWITCH
  1. Disconnect the oil pressure switch connector.

  1. Using a 24 mm deep socket wrench, remove the oil pressure switch.

  1. A058649E01
    Install the oil pressure gauge.

  1. Warm up the engine.

  1. Measure the oil pressure.

    Standard oil pressure:
    Condition
    Specified Condition
    Idle
    29 kPa (0.3 kgf*cm2, 4.3 psi) or more
    3,000 rpm
    294 to 539 kPa (3.0 to 5.5 kgf*cm2, 43 to 78 psi)

    If the oil pressure is not as specified, check the oil pump.

  1. Remove the oil pressure gauge.


9. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH
  1. Remove the 4 bolts and mounting bracket.


10. REMOVE PUMP BRACKET
  1. Remove the 6 bolts and mounting bracket.


11. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

  1. A056838E06
    Remove the 2 bolts (A and B).

  1. Loosen the bolt (C), and remove the No. 1 timing belt idler.


12. REMOVE NO. 2 TIMING BELT IDLER SUB-ASSEMBLY
  1. Remove the bolt, No. 2 timing belt idler and spacer.


13. REMOVE WATER PUMP

  1. A031001E02
    Remove the 6 bolts, tension spring bracket, water pump and gasket.


14. REMOVE CRANKSHAFT TIMING PULLEY

  1. A056898E03
    Using SST, remove the timing pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09953-05020, 09954-05010)


15. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 16 bolts and 2 nuts.

  1. A057637E03
    Insert the blade of SST between the oil pan and cylinder block, and cut off applied sealer and remove the oil pan.
    SST
    09032-00100  

    NOTICE:
    1. Do not use SST for the timing belt case side and rear oil seal retainer.
    2. Do not damage the oil pan flange.


16. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.


17. REMOVE TIMING GEAR CASE SUB-ASSEMBLY

  1. A056912E01
    Remove the 5 bolts, timing gear case and gasket.


18. REMOVE ENGINE REAR OIL SEAL RETAINER
  1. Remove the 4 bolts, oil seal retainer and gasket.


19. INSPECT CONNECTING ROD THRUST CLEARANCE

HINT:
  1. Thoroughly clean all parts to be assembled.
  2. Before installing the parts, apply new engine oil to all sliding and rotating surfaces.
  3. Replace all gaskets, O-rings and oil seals with new ones.

  1. A057169E01
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.080 to 0.300 mm (0.0031 to 0.0118 in.)

    Maximum thrust clearance:
    0.35 mm (0.0138 in.)

    If the thrust clearance is greater than the maximum, replace the connecting rod assembly. If necessary, replace the crankshaft.


20. INSPECT CONNECTING ROD OIL CLEARANCE

  1. A057170E02
    Check the matchmarks on the connecting rod and cap to ensure correct reassembly.

  1. Remove the 2 connecting rod cap nuts.

  1. A057171E01
    Using a plastic hammer, lightly tap the connecting rod bolts and lift off the connecting rod cap.

    HINT:
    Keep the lower bearing inserted with the connecting rod cap.

  1. A057172E01
    Cover the connecting rod bolts with a short piece of hose to protect the crankshaft from damage.

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearing for pitting and scratches.
    If the crank pin or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.

  1. A057173E02
    Lay a strip of Plastigage across the crank pin.

  1. Place the connecting rod cap on the connecting rod.

    1. Match the numbered connecting rod cap with the connecting rod.

    2. A057184E02
      Install the connecting rod cap with the front mark facing forward.

  1. Install the connecting rod cap with the 2 nuts .

    HINT:
    The connecting rod cap nuts are tightened in 2 progressive steps.
    If any connecting rod bolt is broken or deformed replace it.


    1. Apply alight of engine oil to the threads and under the heads of the connecting rod cap nuts.

    2. A057174E01
      Install and alternately tighten the nuts of the connecting rod cap in several passes.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      Do not turn the crankshaft.

    3. Mark the front of the connecting rod cap nuts with paint.

    4. A056296E02
      Retighten the connecting rod cap nuts 90° as shown.

    5. Check that the painted marks is now at a 90° angle to the front.

  1. Remove the 2 nuts, connecting rod cap and lower bearing .

  1. A057175E02
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    Item
    Specified Condition
    STD
    0.036 to 0.064 mm (0.0014 to 0.0025 in.)
    U/S 0.25, U/S 0.50
    0.033 to 0.079 mm (0.0013 to 0.0031 in.)

    Maximum oil clearance:
    0.10 mm (0.0039 in.)

    If the oil clearance is greater than the maximum, replace the bearings. If necessary, grind or replace the crankshaft.

  1. A057176E02
    If using a standard bearing, replace it with one having the same number marked on the connecting rod cap. There are 3 sizes of standard bearings, marked 1, 2 and 3 accordingly.

    Standard sized bearing center wall thickness:
    Mark
    Specified Condition
    1
    1.478 to 1.482 mm (0.0582 to 0.0583 in.)
    2
    1.482 to 1.486 mm (0.0583 to 0.0585 in.)
    3
    1.486 to 1.490 mm (0.0585 to 0.0587 in.)


    1. Completely remove the Plastigage.


21. REMOVE PISTON AND CONNECTING ROD

  1. A056740E03
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. A057172E02
    Cover the connecting rod bolts with a short piece of hose to protect the crankshaft from damage.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearings, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


22. REMOVE PISTON SUB-ASSEMBLY

  1. Check the fitting condition between the piston and piston pin.

    1. A056727E01
      Try to move the piston back and forth on the piston pin.
      If any movement is felt, replace the piston and pin with a new piston and a set.

  1. A056598E01
    Using a piston ring expander, remove the 2 compression rings.

    HINT:
    Be sure to organize the removed piston rings in such a way that they can reinstalled exactly as before.

  1. Remove the oil ring and coil by hand.

    HINT:
    Arrange the piston rings in the correct order.

  1. Disconnect the connecting rod from the piston.

    1. A056731E01
      Using snap ring pliers, remove the 2 snap rings from the piston.

    2. A056730E03
      Gradually heat the piston to approx. 60°C (140°F).

    3. A056729E01
      Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and pin and remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.


23. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A057177E01
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.040 to 0.250 mm (0.0016 to 0.0098 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is greater than the maximum, replace the thrust washers as a set.

    Thrust washer thickness:
    Item
    Specified Condition
    STD
    2.430 to 2.480 mm (0.0957 to 0.0976 in.)
    O/S 0.125
    2.493 to 2.543 mm (0.0981 to 0.1001 in.)
    O/S 0.250
    2.555 to 2.605 mm (0.1006 to 0.1026 in.)


24. REMOVE CRANKSHAFT AND INSPECT OIL CLEARANCE

  1. A057178E02
    Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several passes, in the sequence shown.

  1. A057179E01
    Using the removed crankshaft bearing cap bolts, pry the cap back and forth, and remove the crankshaft bearing caps, lower bearings and lower thrust washers (No. 3 crankshaft bearing cap only).

    HINT:
    1. Keep the lower bearing and crankshaft bearing caps together.
    2. Be sure to organize the bearing caps and lower thrust washers in sure a way that they an be reinstalled exactly as before.

  1. Clean each crankshaft journal and bearing.

  1. Check each crankshaft journal and bearing for pitting and scratches.
    If the journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.

  1. Place the crankshaft on the cylinder block.

  1. A056745E02
    Lay a strip of Plastigage across each journal.

  1. A056294E01
    Install the 5 crankshaft bearing caps in their proper locations.

    NOTICE:
    Do not turn the crankshaft.

  1. Install the crankshaft bearing cap bolts.

    1. Apply a light coat of the engine oil to the threads and under the bolt heads of the crankshaft bearing caps.

    2. A057182E02
      Install and uniformly tighten the 10 bolts of the crankshaft bearing caps, in several steps, in the sequence shown.

      Torque:
      105 N*m{ 1071 kgf*cm , 77 ft.*lbf }

  1. Remove the 10 bolts and 5 crankshaft bearing caps.

  1. A057181E02
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    Item
    Specified Condition
    STD
    0.034 to 0.065 mm (0.0013 to 0.0026 in.)
    U/S 0.25, U/S 0.50
    0.033 to 0.079 mm (0.0013 to 0.0031 in.)

    Maximum oil clearance:
    0.10 mm (0.0039 in.)

    If the oil clearance is greater than the maximum, replace the bearings. If necessary, grind or replace the crankshaft.

  1. A056736E02
    If using a standard bearing, replace it with one having the same number marked on the connecting rod cap. There are 3 sizes of standard bearings, marked 1, 2 and 3 accordingly.

    Standard sized bearing center wall thickness:
    Mark
    Specified Condition
    1
    1.979 to 1.983 mm (0.0779 to 0.0781 in.)
    2
    1.983 to 1.987 mm (0.0781 to 0.0782 in.)
    3
    1.987 to 1.991 mm (0.0782 to 0.0784 in.)

  1. Completely remove the Plastigage.

  1. Lift out the crankshaft.

    HINT:
    Keep the upper crankshaft bearings and upper thrust washers together with the cylinder block.


25. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY
  1. Remove the 4 check valves and oil nozzles.


26. REMOVE CYLINDER BLOCK OIL ORIFICE
  1. Using a 6 mm hexagon wrench, remove the oil orifice.


27. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
  1. Remove the water drain cock from the cylinder block.


28. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and sensor.

← COMPONENTS (from Jun 2011)INSPECTION (from Jun 2011) →