2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2011


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD)

A121844
  1. Remove the 8 bolts and under cover.


3. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD)

A121845
  1. Remove the 4 bolts and under cover.


4. LOOSEN FUEL TANK CAP ASSEMBLY

5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the oil into a container.

  1. Clean the drain plug, and install it with a new gasket.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }


6. DRAIN FUEL

7. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A114241
    Remove the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug and then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A114242E01


8. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts from the transmission.

  1. Remove the 5 clips and front fender seal LH.

  1. Remove the 3 nuts from the exhaust manifold.

  1. Disconnect the front exhaust pipe from the exhaust manifold and remove the gasket.

  1. Remove the bolt, clamp and pipe support from the front exhaust pipe.


9. REMOVE RADIATOR HOSE INLET

10. REMOVE FAN SHROUD
  1. Remove the fan shroud (Click here).


11. REMOVE AIR CLEANER ASSEMBLY
  1. Disconnect the IAT sensor connector.

  1. Loosen the air cleaner hose clamp.

  1. Remove the 3 bolts and air cleaner.


12. DISCONNECT COMPRESSOR AND MAGNET CLUTCH (w/ Air Conditioning System)

  1. A123646
    Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


13. REMOVE COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A112016E01
    Remove the bolt and spacer.

  1. A121135E01
    Remove the 4 bolts and compressor mounting bracket.


14. DISCONNECT HEATER WATER HOSE INLET A
  1. Disconnect the inlet hose (Click here).


15. DISCONNECT HEATER WATER OUTLET HOSE A
  1. Disconnect the outlet hose (Click here).


16. REMOVE TIMING BELT
  1. Remove the timing belt (Click here).


17. REMOVE INTAKE PIPE ASSEMBLY

A123770
  1. Loosen the intake pipe clamp.

  1. Remove the 2 bolts and intake pipe.


18. REMOVE VENTURI ASSEMBLY

  1. A111052E02
    Disconnect the throttle open switch connector.

  1. A111053E02
    Disconnect the throttle control motor connector.

  1. Remove the venturi and gasket.


19. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Remove the 3 bolts and heat insulator.


20. REMOVE INJECTION PIPE SET

  1. A121940
    Using a union nut wrench, loosen the 8 union nuts of the 4 injection pipes.

  1. Remove the 2 nuts, 2 upper pipe clamps and 4 injection pipes with lower pipe clamps.


21. REMOVE NO. 1 GLOW PLUG CONNECTOR
  1. Remove the nut and wire harness.

  1. Remove the 4 screw grommets, 4 nuts and glow plug connector.


22. REMOVE WATER OUTLET HOUSING

  1. A113081
    Remove the 3 bolts, outlet housing and gasket.


23. REMOVE INTAKE MANIFOLD

  1. A113083
    Remove the 6 bolts, 2 nuts, intake manifold and gasket.


24. REMOVE EXHAUST MANIFOLD

  1. A121142
    Remove the 6 bolts, 2 nuts and manifold.

  1. Remove the manifold gasket from the cylinder head.


25. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove the 9 bolts, nut, cylinder head cover and gasket.


26. REMOVE CAMSHAFT TIMING PULLEY

  1. Set the No. 1 cylinder to approx. 90° BTDC/compression.

    HINT:
    Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.


    1. A057443E03
      Using the crankshaft pulley bolt, turn the crankshaft 90°counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

  1. A056901E02
    Using SST, loosen the pulley bolt.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. A056903E02
    Using SST, disconnect the timing pulley from the camshaft.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)

  1. Remove the pulley bolt and timing pulley.

  1. Remove the timing pulley woodruff key.


27. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts and timing belt cover.


28. REMOVE CAMSHAFT OIL SEAL RETAINER
  1. Remove the 4 bolts, retainer and gasket.


29. REMOVE CAMSHAFT

  1. A057786E02
    Turn the camshaft with a wrench so that the key groove faces upward.

  1. A057787E03
    Uniformly loosen and remove the 10 bearing cap bolts, in several steps, in the sequence shown.

  1. Remove the 5 bearing caps and camshaft.

  1. Remove the 10 bearings from the bearing caps and cylinder head.

    HINT:
    Arrange the bearings in the correct order.


30. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A057446E02
    Uniformly loosen and remove the 18 cylinder head bolts, in several steps, in the sequence shown.

    NOTICE:
    Head warpage or cracking could result from removing bolts in an incorrect order.

  1. A056904E01
    Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.

    NOTICE:
    Do not damage the contact surfaces of the cylinder head and cylinder block.

    If the cylinder head is difficult to lift off, pry with a screwdriver between the cylinder head and block.


31. REMOVE CYLINDER HEAD GASKET
  1. Remove the cylinder gasket from the cylinder head.

← COMPONENTS (from Jun 2011)DISASSEMBLY (from Jun 2011) →