Steering Pad Switch Circuit
Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and the radio receiver assembly itself cannot function.
WIRING DIAGRAM


INSPECTION PROCEDURE
- CAUTION:
- The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).
| 1. INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly (Click here).


Text in Illustration *1
Volume+ Switch
*2
Volume- Switch
*3
Seek- Switch
*4
Seek+ Switch
*5
MODE Switch
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
10 (AU1) - 8 (EAU)
No switch is pushed
95 to 105 kΩ
Seek+ switch is pushed
Below 2.5 Ω
Seek- switch is pushed
312.6 to 345.5 Ω
Volume+ switch is pushed
950 to 1050 Ω
Volume- switch is pushed
2954.5 to 3265.5 Ω
9 (AU2) - 8 (EAU)
No switch is pushed
95 to 105 kΩ
MODE switch is pushed
Below 2.5 Ω
|
|
||||
| OK | |
| 2. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Remove the spiral cable sub-assembly (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
8 (EAU) - 4 (EAU)
Spiral cable is turned 2.5 rotations counterclockwise
Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
10 (AU1) - 6 (AU1)
Spiral cable is turned 2.5 rotations counterclockwise
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
9 (AU2) - 5 (AU2)
Spiral cable is turned 2.5 rotations counterclockwise
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
Text in Illustration *a
Steering Pad Switch Side
*b
Vehicle Side
- CAUTION:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here).
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE) |
Disconnect the R17 radio receiver assembly connector.
Disconnect the S42 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R17-21 (SW1) - S42-6 (AU1)
Always
Below 1 Ω
R17-22 (SW2) - S42-5 (AU2)
R17-23 (SWG) - S42-4 (EAU)
R17-21 (SW1) - Body ground
Always
10 kΩ or higher
R17-22 (SW2) - Body ground
R17-23 (SWG) - Body ground
|
|
||||
| OK | ||
| ||
