2014 Hilux · Service Manual ENGINE

P0122 Throttle Position Sensor Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. These troubleshooting procedures are for the throttle position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This throttle valve position sensor is a non-contact type.

The throttle position sensor is mounted on the diesel throttle body and detects the opening angle of the throttle valve. This sensor is electronically controlled and uses Hall-effect elements.
The ECM judges the vehicle's driving conditions from the signals input to its VLU terminal. The data is one of the conditions for EGR control, etc.
G037167E12
DTC No.
DTC Detection Condition
Trouble Area
P0122
Throttle position sensor output (VLU) is less than 0.2 V
(1 trip detection logic)
  1. Throttle position sensor
  2. Open or short in VLU circuit
  3. Open in VC circuit
  4. ECM
P0123
Throttle position sensor output (VLU) is more than 4.8 V
(1 trip detection logic)
  1. Throttle position sensor
  2. Open in E2 circuit
  3. VC and VLU circuits are short-circuited
  4. ECM

MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
G037166E06

WIRING DIAGRAM

A154723E02

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK WIRE HARNESS (THROTTLE POSITION SENSOR - ECM)
G038772E17
  1. Disconnect the E7 and E8 ECM connectors.

  1. Disconnect the T2 throttle position sensor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    E8-18 (VC) - T2-1 (VC)
    Below 1 Ω
    E7-29 (VLU) - T2-3 (VTA)
    Below 1 Ω
    E8-28 (E2) - T2-2 (E2)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    E8-18 (VC) or T2-1 (VC) - Body ground
    10 kΩ or higher
    E7-29 (VLU) or T2-3 (VTA) - Body ground
    10 kΩ or higher
    E8-28 (E2) or T2-2 (E2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2. CHECK ECM (VC VOLTAGE)
A154583E05
  1. Disconnect the T2 throttle position sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E8-18 (VC) - E8-28 (E2)
    4.5 to 5.5 V



NG
REPLACE ECM
OK


3. REPLACE DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE)
  1. Replace diesel throttle body assembly (Click here).


NEXT


4. CHECK IF DTC OUTPUT RECURS (DTC P0122 AND/OR P0123)
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Let the engine idle for 60 seconds.

  1. Repeat quick engine revving to 2,500 rpm for 30 seconds.

  1. Check for DTC(s).

    Result:
    Display (DTC Output)
    Proceed to
    P0122 and/or P0123
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM


← P0122 Throttle Position Sensor Circuit Low Input (+ P0123) (Aug 2013 – Jul 2014)P0168 Fuel Temperature Too High (Jun 2011 – Jul 2012) →