P0122 Throttle Position Sensor Circuit Low Input
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Also covers:
- P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- HINT:
- These troubleshooting procedures are for the throttle position sensor.
- This electrical throttle system does not use a throttle cable.
- This throttle valve position sensor is a non-contact type.
- These troubleshooting procedures are for the throttle position sensor.
The ECM judges the vehicle's driving conditions from the signals input to its VLU terminal. The data is one of the conditions for EGR control, etc.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0122 |
Throttle position sensor output (VLU) is less than 0.2 V (1 trip detection logic) |
|
| P0123 |
Throttle position sensor output (VLU) is more than 4.8 V (1 trip detection logic) |
|
MONITOR DESCRIPTION
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
| 1. CHECK WIRE HARNESS (THROTTLE POSITION SENSOR - ECM) |
![]() ![]() |
Disconnect the E7 and E8 ECM connectors.
Disconnect the T2 throttle position sensor connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
E8-18 (VC) - T2-1 (VC)
Below 1 Ω
E7-29 (VLU) - T2-3 (VTA)
Below 1 Ω
E8-28 (E2) - T2-2 (E2)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
E8-18 (VC) or T2-1 (VC) - Body ground
10 kΩ or higher
E7-29 (VLU) or T2-3 (VTA) - Body ground
10 kΩ or higher
E8-28 (E2) or T2-2 (E2) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK ECM (VC VOLTAGE) |
![]() ![]() |
Disconnect the T2 throttle position sensor connector.
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
- Standard voltage:
Tester Connection
Specified Condition
E8-18 (VC) - E8-28 (E2)
4.5 to 5.5 V
|
|
||||
| OK | |
| 3. REPLACE DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE) |
Replace diesel throttle body assembly (Click here).
| NEXT | |
| 4. CHECK IF DTC OUTPUT RECURS (DTC P0122 AND/OR P0123) |
Clear the DTC(s) (Click here).
Start the engine.
Let the engine idle for 60 seconds.
Repeat quick engine revving to 2,500 rpm for 30 seconds.
Check for DTC(s).
- Result:
Display (DTC Output)
Proceed to
P0122 and/or P0123
A
No output
B
|
|
||||
| A | ||
| ||


