2014 Hilux · Service Manual ENGINE

P0115 Engine Coolant Temperature Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

A thermistor is built in the Engine Coolant Temperature (ECT) sensor and changes the resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.

HINT:
If the ECM detects DTC P0115, P0117 or P0118, it operates the fail-safe function in which the ECT is assumed to be 80°C (176°F).
DTC No.
DTC Detection Condition
Trouble Area
P0115
Open or short in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0117
Short in ECT sensor circuit for 0.5 seconds
(sensor resistance value less than 79 Ω)
P0118
Open in ECT sensor circuit for 0.5 seconds
(sensor resistance value more than 156 kΩ)
(1 trip detection logic)


HINT:
When DTC P0115, P0117 and/or P0118 is detected, check the engine coolant temperature by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Coolant Temp.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit


WIRING DIAGRAM

A110950E26

INSPECTION PROCEDURE

HINT:
  1. If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
If the ECM is replaced, the new ECM needs initialization (Click here).


1. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the values.

    OK:
    75 to 95°C (167 to 203°F) after warming up the engine.

    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    OK (Same as actual engine coolant temperature)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or more.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
A096620E05
  1. Disconnect the W1 ECT sensor connector.

  1. Connect terminals 1 and 2 of the ECT sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the values.

    Standard:
    140°C (284°F) or more



OK
CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR
NG


3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
A099842E65
  1. Disconnect the W1 ECT sensor connector.

  1. Connect terminals THW and E2 of the E8 ECM connector.

    HINT:
    Before checking, perform a visual and contact pressure check on the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the values.

    Standard:
    140°C (284°F) or more



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

CONFIRM GOOD CONNECTION AT ECM. IF OK, REPLACE ECM

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
G038989E04
  1. Disconnect the W1 ECT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the values.

    Standard:
    -40°C (-40°F)



OK
CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR
NG


5. INSPECT INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
A099843E41
  1. Disconnect the W1 ECT sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the values.

    Standard:
    -40°C (-40°F)



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

REPLACE ECM (Click here)


← P0115 Engine Coolant Temperature Circuit (+ P0117, P0118) (Aug 2013 – Jul 2014)P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input (+ P0123) (Jun 2011 – Jul 2012) →