P0335 Crankshaft Position Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Also covers:
- P0339 Crankshaft Position Sensor "A" Circuit Intermittent
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail injection system is controlled.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0335 |
When either condition below is met:
|
|
| P0339 |
No crankshaft position sensor signal to ECM is input for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.
- Installation condition of the camshaft position sensor
- Installation condition of the camshaft
- Connection of the camshaft position sensor connector
- Installation condition of the camshaft position sensor
- HINT:
- If no trouble is found in the diagnostic troubleshooting procedure of DTC P0335, troubleshoot the engine mechanical system.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- If no trouble is found in the diagnostic troubleshooting procedure of DTC P0335, troubleshoot the engine mechanical system.
- NOTICE:
- If the ECM is replaced, the new ECM needs initialization (Click here).
| 1. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
![]() ![]() |
Disconnect the C4 sensor connector.
Measure the resistance of the sensor.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
1,630 to 2,740 Ω
1 - 2
Hot
2,065 to 3,225 Ω
- NOTICE:
- In the chart above, the terms "cold" and "hot" refer to the temperature of the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).
- HINT:
-


- While cranking or idling the engine, check the waveform of the ECM connectors using an oscilloscope.
- Reference:
Tester Connection
Specified Condition
E7-23 (G+) - E7-31 (G-)
E8-27 (NE+) - E8-34 (NE-)
Correct waveform is shown
Tool Setting
Condition
5 V/DIV., 20 msec./DIV.
Idling with warm engine
- HINT:
- The waveform varies depending on the engine speed.
|
|
||||
| OK | |
| 2. CHECK WIRE HARNESS (CRANKSHAFT POSITION SENSOR - ECM) |
![]() ![]() |
Disconnect the C4 sensor connector.
Disconnect the E8 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
C4-1 - E8-27 (NE+)
Below 1 Ω
C4-2 - E8-34 (NE-)
Below 1 Ω
C4-1 or E8-27 (NE+) - Body ground
10 kΩ or higher
C4-2 or E8-34 (NE-) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() ![]() |
Check the sensor installation.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 4. CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
Check the teeth of the crankshaft position sensor No. 1 plate.
- OK:
- Plate's teeth do not have any cracks or deformation.
|
|
||||
| OK | ||
| ||



