2014 Hilux · Service Manual TRANSMISSION

U0100 Lost Communication with ECM / PCM "A"

Diagnostic trouble codes · Vehicles built from Jun 2011

DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communications with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine rpm, required engine torques, warning indicators in the combination meter, DTCs and other data. The ECM sends signals to the TCM concerning engine rpm, opening angles of the throttle valve, temperature of the intake air and engine coolant, engine torques, and other data.
If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN system, illuminate the MIL and set a DTC.
DTC Code
DTC Detection Condition
Trouble Area
U0100
No communication from ECM continues (1 trip detection logic)
  1. Open or short in TCM and ECM circuit
  2. TCM
  3. ECM

WIRING DIAGRAM

C245094E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
If the ECM is replaced, the new ECM needs initialization.


1. CHECK ECM (VC, +B VOLTAGE, E1 GROUND)
C245095E01
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    w/ DPF 
    Tester Connection
    Switch Condition
    Specified Condition
    E31-24 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    E27-13 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V
    w/o DPF 
    Tester Connection
    Switch Condition
    Specified Condition
    E5-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    E8-18 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V


    Standard Resistance:
    w/ DPF 
    Tester Connection
    Condition
    Specified Condition
    E25-1 (E1) - Body ground
    Always
    Below 1 Ω
    w/o DPF 
    Tester Connection
    Condition
    Specified Condition
    E7-7 (E1) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*A
w/ DPF
*B
w/o DPF
*a
Rear view of wire harness connector
(to ECM)


NG
INSPECT +B, E1 CIRCUIT (ECM POWER SOURCE CIRCUIT OR VC CIRCUIT)
OK


2. CHECK TCM (IG2 VOLTAGE, E1 GROUND)
C191543E21
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T38-6 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-1 (E1) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Rear view of wire harness connector
(to TCM)


NG
INSPECT IG2, E1 CIRCUIT (TCM POWER SOURCE CIRCUIT)
OK


3. CHECK HARNESS AND CONNECTOR (ECM - TCM)
  1. Disconnect the E24*1 or E6*2 ECM connector.

    1. *1: w/ DPF
    2. *2: w/o DPF

  1. Disconnect the T38 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ DPF 
    Tester Connection
    Condition
    Specified Condition
    E24-24 (CAN+) - T38-21 (CAN+)
    Always
    Below 1 Ω
    E24-18 (CAN-) - T38-20 (CAN-)
    Always
    Below 1 Ω
    E24-24 (CAN+) or T38-21 (CAN+) - Body ground
    Always
    10 kΩ or higher
    E24-18 (CAN-) or T38-20 (CAN-) - Body ground
    Always
    10 kΩ or higher
    w/o DPF 
    Tester Connection
    Condition
    Specified Condition
    E6-22 (CAN+) - T38-21 (CAN+)
    Always
    Below 1 Ω
    E6-21 (CAN-) - T38-20 (CAN-)
    Always
    Below 1 Ω
    E6-22 (CAN+) or T38-21 (CAN+) - Body ground
    Always
    10 kΩ or higher
    E6-21 (CAN-) or T38-20 (CAN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CONFIRM DTC
  1. Clear the DTC.

  1. Replace the TCM.

    HINT:
    Replace the TCM with a TCM from a normally functioning vehicle of the same model.

  1. Start the engine.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    U0100 is not output
    A
    U0100 is output
    B



B
REPLACE ECM
A

REPLACE TCM


← P2772 Four Wheel Drive (4WD) Low Switch Circuit Range / Performance (from Jun 2011)TCM Power Source Circuit (from Jun 2011) →