2014 Hilux · Service Manual TRANSMISSION

P2772 Four Wheel Drive (4WD) Low Switch Circuit Range / Performance

Diagnostic trouble codes · Vehicles built from Aug 2012

DESCRIPTION

The TCM detects the signal from the No. 1 transfer indicator switch (L4 position switch).
This DTC indicates that the transfer L4 position switch remains ON.
DTC Code
DTC Detection Condition
Trouble Area
P2772
  1. Transfer L4 position switch remains ON while vehicle is running under following conditions for 1.8 seconds or more (1-trip detection logic):
    1. Output shaft speed 3000 rpm or less
    2. Transfer shift position is H
  1. Short in transfer L4 position switch circuit
  2. Transfer L4 position switch
  3. TCM

MONITOR DESCRIPTION

The TCM monitors the transfer L4 position switch to determine when the transfer-case L4 gear is engaged. If the transfer-case L4 gears remain engaged under all of the following conditions, the TCM will conclude that there is a malfunction of the transfer L4 position switch:
  1. The transfer L4 position switch indicates that the L4 transfer-case gears are engaged.
  2. Transfer-case shift lever is in the "H" position.
  3. Transfer-case output shaft rpm is between 750 and 3000 rpm.
  4. The specified time period has elapsed.
Then the TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C154998E51

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - BODY GROUND)

  1. C237849E09
    Disconnect the No. 1 transfer indicator switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T4-2 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector:
    (to No. 1 Transfer Indicator Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT NO. 1 TRANSFER INDICATOR SWITCH (L4 POSITION SWITCH)

  1. C237865E01
    Remove the No. 1 transfer indicator switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩ or higher
    1 - 2
    Pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 transfer indicator switch)
    *b
    Pushed
    *c
    Not pushed



NG
REPLACE NO. 1 TRANSFER INDICATOR SWITCH (L4 POSITION SWITCH)
OK


3. CHECK HARNESS AND CONNECTOR (NO. 1 TRANSFER INDICATOR SWITCH - TCM)
  1. Disconnect the T4 No. 1 transfer indicator switch connector.

  1. Disconnect the T37 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T4-1 - T37-15 (L4)
    Always
    Below 1 Ω
    T4-1 or T37-15 (L4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← P2769 Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL) (+ P2770) (from Aug 2012)U0100 Lost Communication with ECM / PCM "A" (Aug 2012 – Jul 2013) →