2014 Hilux · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012

DESCRIPTION

While the engine is being cranked, positive (+) battery voltage is applied to terminal STA of the ECM. If the vehicle is being driven and the ECM detects the starter control signal (STA), the ECM concludes that the starter control circuit is malfunctioning. The ECM will illuminate the MIL and set a DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met and battery (+B) voltage of 10.5 V or more is applied for 20 seconds.
(a) Vehicle speed is greater than 20 km/h (12 mph)
(b) Engine revolution is greater than 1,000 rpm
(c) STA signal ON
  1. Short in PNP switch circuit
  2. Park/Neutral position switch assembly
  3. Ignition switch
  4. ECM

WIRING DIAGRAM

A177989E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ DATA LIST (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned to ON and START.

Result:
Ignition Switch Position
STA Signal
Proceed to
ON → START
for A/T:
Display does not change from OFF → ON
A
ON → START
for M/T:
Display does not change from OFF → ON
B
ON → START
Display changes from OFF → ON
C



B
Go to step 3

C
REPLACE ECM
A


2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
A093221E23
  1. Move the shift lever to the P or N position.

  1. Disconnect the N8 Park/Neutral Position (PNP) switch connector.

  1. Measure the resistance of the PNP switch.

    Standard:
    Tester Connection
    Shift Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    4 (B) - 5 (L)
    Except P or N
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


3. INSPECT IGNITION SWITCH ASSEMBLY
A056879E07
  1. Measure the resistance of the I6 ignition switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 7
    LOCK
    10 kΩ or higher
    5 - 7
    START
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK


4. CHECK IF DTC OUTPUT RECURS
  1. Clear the DTCs.

  1. Drive the vehicle at more than 40 km/h (25 mph) for 20 seconds or more.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTC.

    Result:
    Display (DTC Output)
    Proceed to
    P0617 is output again
    A
    No DTC is output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0617 Starter Relay Circuit High (Jun 2011 – Jul 2012)P1603 Engine Stall History (+ P1605) (from Aug 2014) →