2014 Hilux · Service Manual ENGINE

Variable Resistor Circuit

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

This resistor is used to change the air-fuel ratio of the air-fuel mixture.
The idle mixture is adjusted using this resistor.
Turning the idle mixture adjusting screw clockwise moves the contacts inside the resistor, raising the terminal VAF voltage. Conversely, turning the screw counterclockwise lowers the terminal VAF voltage.
When the terminal VAF voltage rises, the ECM increases the injection volume slightly, making the air-fuel mixture a little richer.

WIRING DIAGRAM

A121674E01

INSPECTION PROCEDURE


1. CHECK CO/HC
A110999E01
  1. Warm up the engine to normal operating temperature.

  1. Turn all accessories OFF.

  1. Connect all vacuum lines properly.

  1. Connect the tachometer.

  1. Check ignition timing correctly.

  1. Check idle speed correctly.

  1. Check that the CO meter is properly calibrated.

  1. Race the engine at 2,500 rpm about 2 minutes.

  1. Insert a tester probe at least 40 cm (1.3 ft.) into the tailpipe.

  1. Measure the concentration with 1 to 3 minutes after racing the engine to allow the concentration to stabilize.

    Idle CO concentration:
    1 to 2%



OK
CHECK FOR PROBLEM SYMPTOMS TABLE
NG


2. ADJUST CO CONCENTRATION
A073579E01
  1. Put the vehicle in the same condition as the previous step (CHECK CO/HC).

  1. Using SST, adjust the idle mixture by turning the idle mixture adjusting screw in the variable resistor.

    Result 
    Result
    Proceed
    Concentration: 1.5 +- 0.5%
    B
    Change in CO concentration
    C
    No change in CO concentration
    A

    HINT:
    1. Always check idle speed after turning the idle mixture adjusting screw. If it is incorrect, readjust idle speed.
    2. The idle mixture adjusting screw can be turned within 180°. Do not turn this screw more than specified.

SST
09243-00020  


B
ADJUSTMENT COMPLETE

C
CHECK CO/HC
A


3. INSPECT VARIABLE RESISTOR
A074545E01
  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    1 - 2
    3.5 to 6.5 Ω

  1. While fully turning the idle mixture adjusting screw clockwise and counterclockwise using SST, measure the resistance.

    Resistance:
    Tester Connection
    Specified Condition
    2 - 3
    Resistance changes from approximately 5 to 0 kΩ

SST
09243-00020  


NG
REPLACE VARIABLE RESISTOR
OK


4. CHECK ECM (VAF VOLTAGE)
G038493E03
  1. Turn the ignition switch ON.

  1. While fully turning the idle mixture adjusting screw clockwise and counterclockwise slowly using SST, measure the voltage.

    Standard voltage:
    Tester Connection
    Specified Condition
    E12-25 (VAF) - E12-28 (E2)
    Voltage changes smoothly from 0 to approximately 5 V (does not change suddenly)

SST
09243-00020  


OK
REPLACE ECM
NG


5. CHECK WIRE HARNESS (VARIABLE RESISTOR - ECM)
A113859E01
  1. Disconnect the V4 variable resistor connector.

  1. Disconnect the E12 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    V4-2 (VC) - E12-18 (VC)
    Below 1 Ω
    V4-3 (VAF) - E12-25 (VAF)
    Below 1 Ω
    V4-1 (E2) - E12-28 (E2)
    Below 1 Ω
    V4-2 (VC) or E12-18 (VC) - Body ground
    10 kΩ or higher
    V4-3 (VAF) or E12-25 (VAF) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← Starter Signal Circuit (from Aug 2012)Brake Override System (Jun 2011 – Jul 2012) →