2014 Hilux · Service Manual ENGINE

Starter Signal Circuit

Circuit diagnosis · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012

DESCRIPTION

When the engine is cranked, the intake air flow becomes slow, so fuel vaporization is poor. A rich mixture is therefore necessary in order to achieve good startability. While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel injection volume for starting and after-start injection control.

WIRING DIAGRAM

A177989E01

INSPECTION PROCEDURE


When using intelligent tester:


1. READ DATA LIST (STA SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned to ON and START.

    Result:
    Ignition Switch Position
    STA Signal
    Proceed to
    ON → START
    for A/T:
    Display does not change for OFF → ON
    A
    for M/T:
    Display does not change for OFF → ON
    B
    Display changes from OFF → ON
    C



B
Go to step 3

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A


2. INSPECT PARK/NEUTRAL POSITION SWITCH
A093221E23
  1. Move the shift lever to the P or N position.

  1. Disconnect the N8 Park/Neutral Position (PNP) switch connector.

  1. Measure the resistance of the PNP switch.

    Standard:
    Tester Connection
    Shift Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    4 (B) - 5 (L)
    Except P or N
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (GO TO NEXT STEP AFTER REPLACEMENT)
OK


3. CHECK WIRE HARNESS (ECM - IGNITION SWITCH)
G034713E01
  1. Disconnect the E9 ECM connector.

  1. Disconnect the I6 ignition switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E9-12 (STA) - I6-7 (ST2)
    Below 1 Ω
    E9-12 (STA) or I6-7 (ST2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
REPLACE IGNITION SWITCH (GO TO NEXT STEP AFTER REPLACEMENT)
OK


5. DATA LIST (STA SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned to ON and START.

    OK:
    Ignition Switch Position
    STA Signal
    ON → START
    Display changes from OFF → ON



NG
REPLACE ECM
OK

END


When not using intelligent tester:


1. CHECK ECM (STA VOLTAGE)
A066060E24
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E9-12 (STA) - E12-3 (E1)
    0 V

  1. Measure the voltage of the ECM connectors when the engine is cranked.

    Standard voltage:
    Tester Connection
    Specified Condition
    E9-12 (STA) - E12-3 (E1)
    6 V or more

Result 
Result
Proceed to
NG for A/T
A
NG for M/T
B
OK
C


B
Go to step 3

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A


2. INSPECT PARK/NEUTRAL POSITION SWITCH
A093221E23
  1. Move the shift lever to the P or N position.

  1. Disconnect the N8 Park/Neutral Position (PNP) switch connector.

  1. Measure the resistance of the PNP switch.

    Standard:
    Tester Connection
    Shift Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    4 (B) - 5 (L)
    Except P or N
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH
OK


3. CHECK WIRE HARNESS (ECM - IGNITION SWITCH)
G034713E01
  1. Disconnect the E9 ECM connector.

  1. Disconnect the I6 ignition switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E9-12 (STA) - I6-7 (ST2)
    Below 1 Ω
    E9-12 (STA) or I6-7 (ST2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
REPLACE IGNITION SWITCH
OK

REPLACE ECM


← Starter Signal Circuit (Jun 2011 – Jul 2012)Variable Resistor Circuit (from Jun 2011) →