2014 Hilux · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Jun 2011


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (4WD)

3. REMOVE NO. 2 ENGINE COVER SUB-ASSEMBLY (4WD)

4. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (4WD)

5. REMOVE REAR PROPELLER SHAFT ASSEMBLY

6. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

7. REMOVE CLUTCH RELEASE BEARING ASSEMBLY

8. REMOVE CLUTCH RELEASE FORK BOOT

9. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

10. REMOVE RELEASE BEARING HUB CLIP

11. REMOVE RELEASE FORK SUPPORT
  1. Remove the release fork support from the manual transmission unit.


12. REMOVE CLUTCH COVER ASSEMBLY

  1. D029616E01
    Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


13. REMOVE CLUTCH DISC ASSEMBLY

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.


14. INSPECT INPUT SHAFT FRONT BEARING

  1. Q002481E01
    Turn the bearing by hand by applying rotational force.
    If the bearing sticks or has much resistance, replace the input shaft bearing.

    HINT:
    The bearing is permanently lubricated and requires no cleaning or lubrication.


15. REMOVE INPUT SHAFT FRONT BEARING

  1. Q007150E01
    Remove any 2 diametrically opposite bolts.

  1. Using SST, remove the input shaft bearing.

    SST
    09303-35011  


16. INSPECT CLUTCH DISC ASSEMBLY

NOTICE:
When replacing the clutch disc assembly, make sure to perform an inspection of the flywheel subassembly and clutch cover assembly.

  1. C062956E01
    Using a vernier caliper, measure the rivet head depth.

    Minimum rivet depth:
    0.3 mm (0.012 in)

    If the depth is less than the minimum, replace the clutch disc assembly.

  1. CL00373E01
    Install the clutch disc to the transmission unit.

    NOTICE:
    Be careful not to insert the clutch disc facing the wrong direction.

  1. Using a dial indicator, check the disc runout.

    Maximum runout:
    0.8 mm (0.031 in.)

    If the runout is greater than the maximum, replace the clutch disc assembly.


17. INSPECT CLUTCH COVER ASSEMBLY

  1. D025281E01
    Using a vernier caliper, measure the depth and width of the worn areas of the diaphragm spring.

    Maximum:
    Measurement
    Maximum
    A (Depth)
    0.5 mm (0.020 in.)
    B (Width)
    6.0 mm (0.236 in.)

    If the depth or width is greater than the maximum, replace the clutch cover assembly.

    NOTICE:
    When replacing the clutch disc assembly, make sure to perform an inspection of the flywheel subassembly and clutch cover assembly.


18. INSPECT FLYWHEEL SUB-ASSEMBLY

  1. Q007250E01
    Using a dial indicator, measure the flywheel runout.

    Maximum runout:
    0.1 mm (0.004 in.)

    If the runout is greater than the maximum, replace the flywheel sub-assembly.

    NOTICE:
    When replacing the clutch disc assembly, make sure to perform an inspection of the flywheel subassembly and clutch cover assembly.


19. INSPECT CLUTCH RELEASE BEARING ASSEMBLY

  1. N000414E01
    Turn the bearing by hand while applying force in the axial direction.
    If the bearing sticks or has much resistance, replace the release bearing.

    HINT:
    The bearing is permanently lubricated and requires no cleaning or lubrication.

← COMPONENTS (from Aug 2013)INSTALLATION (Jun 2011 – Jul 2012) →