INSPECTION
Inspection · Vehicles built from Jun 2011
| INSPECT REAR CLUTCH DISC |
![]() ![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
- NOTICE:
- Before assembling new discs, soak them in ATF for at least 15 minutes.
| INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY |
![]() ![]() |
Using a dial indicator, measure the inside diameter of the reverse clutch hub bushing.
- Standard drum bushing:
- 35.812 to 35.837 mm (1.4099 to 1.4109 in.)
- Maximum drum bushing:
- 35.887 mm (1.4129 in.)
- If the inside diameter is greater than the maximum, replace the reverse clutch hub.
| INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY |
![]() ![]() |
Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.
- Standard drum bushing:
- 26.037 to 26. 062 mm (1.0251 to 1.0261 in.)
- Maximum drum bushing:
- 26.112 mm (1.028 in.)
- If the inside diameter is greater than the maximum, replace the forward clutch hub.
| INSPECT FORWARD MULTIPLE DISC CLUTCH DISC |
![]() ![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
- NOTICE:
- Before assembling new discs, soak them in ATF for at least 15 minutes.
| INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() ![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
- Standard free length:
- 26.74 mm (1.053 in.)
| INSPECT DIRECT CLUTCH DISK |
![]() ![]() |
Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.
- NOTICE:
- Before assembling new discs, soak them in ATF for at least 15 minutes.
| INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() ![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
- Standard free length:
- 21.04 mm (0.828 in.)
| INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() ![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
- Standard free length:
- 19.51 mm (0.768 in.)
| INSPECT PACK CLEARANCE OF DIRECT CLUTCH |
![]() ![]() |
Using a dial gauge, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while blowing air from the oil hole as shown in the illustration, and calculate the average.
- Pack clearance:
- 0.5 to 0.8 mm (0.020 to 0.031 in.)
- NOTICE:
- Install a selective flange (3.4 mm (0.134 in.)) when measuring the moving distance (shaded area in the illustration.)
- HINT:
- Flange moving distance A = 0.26 to 1.14 mm (0.010 to 0.045 in.)
- Pack clearance = Flange moving distance A - 0.05 mm (0.002 in.)
If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.
- Flange thickness:
No.
Thickness
No.
Thickness
0
3.0 mm (0.118 in.)
5
3.5 mm (0.138 in.)
1
3.1 mm (0.122 in.)
6
3.6 mm (0.142 in.)
2
3.2 mm (0.126 in.)
7
3.7 mm (0.146 in.)
3
3.3 mm (0.130 in.)
8
3.8 mm (0.150 in.)
4
3.4 mm (0.134 in.)
-
-
| INSPECT PACK CLEARANCE OF REVERSE CLUTCH |
Using a dial gauge, measure the reverse clutch piston stroke (distance A) and the moving distance (distance B) of the reverse flange at the both ends across a diameter while blowing air (392 kPa, 4 kgf/cm2, 57 psi) from the oil hole as shown in the illustration, and calculate the average.
- Pack clearance:
- 0.5 to 0.8 mm (0.020 to 0.031 in.)
- NOTICE:
- Install a selective flange (3.3 mm (0.130 in.)) when measuring the moving distance (shaded area in the illustration.)
- HINT:
- Piston stroke A = 1.05 to 2.15 mm (0.041 to 0.085 in.)
- Flange moving distance B = 0.72 to 1.08 mm (0.029 to 0.043 in.)
- Pack clearance = Piston stroke A to Flange moving distance B to 0.06 mm (0.002 in.)


If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.
- Flange thickness:
No.
Thickness
No.
Thickness
0
2.8 mm (0.110 in.)
6
3.4 mm (0.134 in.)
1
2.9 mm (0.114 in.)
7
3.5 mm (0.138 in.)
2
3.0 mm (0.118 in.)
8
3.6 mm (0.142 in.)
3
3.1 mm (0.122 in.)
9
3.7 mm (0.146 in.)
4
3.2 mm (0.126 in.)
A
3.8 mm (0.150 in.)
5
3.3 mm (0.130 in.)
-
| INSPECT PACK CLEARANCE OF FORWARD CLUTCH |
![]() ![]() |
Using a dial gauge, measure the moving distance (distance A) of the clutch flange at boths end across a diameter while blowing air from the oil hole as shown in the illustration, and calculate the average.
- Pack clearance:
- 0.6 to 0.9 mm (0.024 to 0.354 in.)
- NOTICE:
- Install a selective flange (3.4 mm (0.134 in.)) when measuring the moving distance (shaded area in the illustration.)
- HINT:
- Flange moving distance A = 0.26 to 1.36 mm (0.010 to 0.054 in.)
- Pack clearance = Flange moving distance A to 0.01 mm (0.0003 in.)
If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.
- Flange thickness:
No.
Thickness
No.
Thickness
0
3.0 mm (0.118 in.)
6
3.6 mm (0.142 in.)
1
3.1 mm (0.122 in.)
7
3.7 mm (0.146 in.)
2
3.2 mm (0.126 in.)
8
3.8 mm (0.150 in.)
3
3.3 mm (0.130 in.)
9
3.9 mm (0.154 in.)
4
3.4 mm (0.134 in.)
A
4.0 mm (0.158 in.)
5
3.5 mm (0.138 in.)
-






