2014 Hilux · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

D027995E01
  1. Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.


2. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

D027996E01
  1. Using a screwdriver, remove the snap ring from the clutch drum and input shaft assembly.

  1. D027997E01
    Remove the reverse clutch hub sub-assembly, reverse clutch reaction sleeve, clutch cushion, plate reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the clutch drum assembly.


3. REMOVE REVERSE CLUTCH REACTION SLEEVE

D027998E01
  1. Remove the reverse clutch reaction sleeve from the reverse clutch hub sub-assembly.


4. REMOVE REAR CLUTCH DISC

D027999E05
  1. Remove the clutch cushion plate, reverse clutch flange, 4 plates and 5 discs from the reverse clutch hub.


5. INSPECT REAR CLUTCH DISC

D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


6. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY

D028000E01
  1. Using a dial indicator, measure the inside diameter of the reverse clutch hub bushing.

    Standard drum bushing:
    35.812 to 35.837 mm (1.4099 to 1.4109 in.)

    Maximum drum bushing:
    35.887 mm (1.4129 in.)

    1. If the inside diameter is greater than the maximum, replace the reverse clutch hub.


7. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

D028001E01
  1. Remove the forward clutch hub sub-assembly from the clutch drum assembly.

  1. D028500E03
    Remove the 2 thrust needle roller bearings from the forward clutch hub sub-assembly.


8. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

D028501E01
  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

    Standard drum bushing:
    26.037 to 26. 062 mm (1.0251 to 1.0261 in.)

    Maximum drum bushing:
    26.112 mm (1.028 in.)

    1. If the inside diameter is greater than the maximum, replace the forward clutch hub.


9. REMOVE MULTIPLE DISC CLUTCH HUB

D028502E01
  1. Remove the multiple disc clutch hub from the clutch drum assembly.

  1. D028503E02
    Remove the No. 2 thrust bearing race and input shaft thrust bearing race rear from the multiple disc clutch hub.


10. REMOVE INPUT SHAFT ASSEMBLY

D028504E01
  1. Remove the thrust needle roller bearing from the clutch drum assembly.

  1. D028505E01
    Remove the input shaft assembly from the clutch drum assembly.


11. REMOVE INPUT SHAFT OIL SEAL RING

D029677E01
  1. Remove the 3 oil seal rings from the input shaft assembly.


12. REMOVE FORWARD MULTIPLE DISC CLUTCH DISC

D028519E01
  1. Using a screwdriver, remove the hole snap ring

  1. D028520E01
    Remove the 2 flanges, 6 discs and 5 plates from the input shaft assembly.


13. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


14. REMOVE NO. 1 CLUTCH BALANCER

D028521E02
  1. Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

    SST
    09350-30020   (09350-07040, 09350-07070)

  1. D028522E01
    Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft assembly.

  1. D028523E01
    Remove the O-ring from the No. 1 clutch balancer.


15. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    26.74 mm (1.053 in.)


16. REMOVE FORWARD CLUTCH PISTON

D028524E01
  1. Holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the input shaft to remove the forward clutch piston.

  1. D028525E01
    Remove the 2 O-rings from the forward clutch piston.


17. REMOVE REVERSE CLUTCH FLANGE

D028506E01
  1. Remove the reverse clutch flange from the clutch drum assembly.


18. REMOVE DIRECT CLUTCH DISK

D028507E01
  1. Using a screwdriver, remove the 2 hole snap rings from the clutch drum assembly.

  1. D028508E03
    Remove the reverse clutch flange, 6 plates and 5 discs from the clutch drum assembly.


19. INSPECT DIRECT CLUTCH DISK

20. REMOVE NO. 3 CLUTCH BALANCER

  1. D028509E03
    Place SST on the No. 3 clutch balancer, and compress the return spring with a press.
    SST
    09387-00070  
    09350-30020   (09350-07070)


21. REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

D028510E01
  1. Remove the reverse clutch return spring and O-ring from the reverse clutch piston.


22. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.04 mm (0.828 in.)


23. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

D028511E01
  1. Remove the reverse clutch piston, sub-assembly from the clutch drum sub-assembly.

  1. D028512E01
    Remove the O-ring from the reverse clutch piston sub-assembly.

  1. D028513E01
    Remove the O-ring from the clutch drum sub-assembly.


24. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

D028514E05
  1. Place SST on the direct clutch piston, and compress the return spring with a press.

    SST
    09320-89010  
    09350-30020   (09350-07070)

  1. D028515E01
    Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the clutch drum.

  1. D028516E01
    Remove the O-ring from the clutch drum.

  1. D028517E01
    Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston sub-assembly.

  1. D028816E01
    Remove the 2 O-rings from the direct clutch piston sub-assembly.


25. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.51 mm (0.768 in.)

← COMPONENTS (from Jun 2011)INSPECTION (from Jun 2011) →