2014 Hilux · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Jun 2011


INSPECT STARTER ASSEMBLY

A111845E01

CAUTION:
These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Perform pull-in test.

    1. Remove the nut, and then disconnect the field coil lead wire from terminal C.

    2. Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.

      A111846E01

  1. Perform holding test.

    1. When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.
      If the clutch pinion gear moves inward, replace the magnet starter switch assembly.

      A111847E01

  1. Inspect clutch pinion gear return.

    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.

      A111848E01

  1. Perform operation test without load.

    1. Connect the field coil lead wire to terminal C with the nut.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. Mount the starter in a vise between aluminum plates.

    3. Connect the battery and an ammeter to the starter as shown in the illustration.

      A111849E01

    4. Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

      Standard current:
      100 A or less at 11.5 V

      If the result is not as specified, replace the starter assembly.


INSPECT STARTER ARMATURE ASSEMBLY

  1. Measure the resistance.

    1. A115023E01
      Measure the resistance between any 2 segments of the commutator.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.

    2. A115024E01
      Measure the resistance between each segment of the commutator and the armature coil core.

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace the armature assembly.

  1. A115025
    Inspect circle runout.

    1. Place the armature on V-blocks.

    2. Using a dial gauge, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.0020 in.)

      If the circle runout is greater than the maximum, replace the armature assembly.

  1. A115026
    Using a vernier caliper, measure the commutator diameter.

    Standard commutator diameter:
    35.0 mm (1.378 in.)

    Minimum commutator diameter:
    34.0 mm (1.339 in.)

    If the diameter is less than the minimum, replace the armature assembly.

  1. A115027
    Measure the undercut depth of the commutator.

    Standard undercut depth:
    0.7 mm (0.028 in.)

    Minimum undercut depth:
    0.2 mm (0.008 in.)

    If the undercut depth is less than the minimum, correct it with a hacksaw blade.

  1. Inspect the armature bearings.

    1. Check that the armature bearings rotate smoothly.
      If the result is not as specified, replace the armature assembly.


INSPECT STARTER YOKE ASSEMBLY

  1. A115028
    Inspect the field coil for an open circuit.

    1. Measure the resistance between the lead wire and field coil brush lead.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

  1. A115030
    Inspect the shunt coil for an open circuit.

    1. Measure the resistance between the shunt coil terminals.

      Standard resistance:
      1.5 to 1.9 Ω at 20°C (68°F)

      If the result is not as specified, replace the starter yoke assembly.


INSPECT BRUSH

  1. A115031
    Using a vernier caliper, measure the brush length.

    Standard length:
    15.0 mm (0.591 in.)

    Minimum length:
    9.0 mm (0.354 in.)

    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A115033
    Inspect the brush insulation.

    1. Using an ohmmeter, measure the resistance between the positive and negative brush holders.

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace the brush holder assembly.

  1. A115032
    Take a pull scale reading the instant the brush spring separates from the brush.

    Standard spring load:
    21.5 to 27.5 N (2.2 to 2.8 kgf, 4.8 to 6.2 lbf)

    Minimum spring load:
    12.7 N (1.3 kgf, 2.9 lbf)

    If the spring load is less than the minimum, replace the brush spring.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A115056E01
    Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    If the result is not as specified, replace the starter clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. Check if the pull-in coil has an open circuit.

    1. A197150E01
      Measure the resistance between terminal 50 and terminal C.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  1. Check if the hold-in coil has an open circuit.

    1. A197151E01
      Measure the resistance between terminal 50 and the switch body.

      Standard resistance:
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

← DISASSEMBLY (from Jun 2011)REASSEMBLY (from Jun 2011) →