INSTALLATION
Removal / installation · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
| 1. CLEAN TURBOCHARGER SUB-ASSEMBLY |
| 2. INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY (w/ Intercooler) |
Connect the No. 1 turbo water hose to the No. 1 turbo water pipe sub-assembly, and slide the clamp to secure the hose.
Install a new gasket and the No. 1 turbo water pipe sub-assembly with the bolt and 2 nuts.

- Torque:
- for bolt:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
- for nut:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }
Text in Illustration *1
Gasket
| 3. INSTALL TURBOCHARGER SUB-ASSEMBLY |
Install a new gasket and the turbocharger sub-assembly with 3 new nuts to the exhaust manifold.
- Torque:
- 52 N*m{ 530 kgf*cm , 38 ft.*lbf }
w/o Intercooler:
Temporarily install a new gasket and the turbo oil pipe sub-assembly with the 2 nuts, but only loosely install the nuts.

Text in Illustration *1
Gasket
*2
Turbo Oil Pipe Sub-assembly
*a
Narrow
*b
Wide


Outside
- NOTICE:
- The notch (wide part) of the gasket must face the engine.
Install a new gasket (labeled A) and the turbo oil pipe sub-assembly with the 2 bolts, but only loosely install the bolts.

Text in Illustration *1
Gasket
*2
Turbo Oil Pipe Sub-assembly
*3
Union Bolt
*4
Manifold Stay
*a
Craw


Turbo Oil Pipe Side
- NOTICE:
- The claws of the gasket must face the turbo oil pipe sub-assembly.
Install a new gasket (labeled B) and the turbo oil pipe sub-assembly with the union bolt, but only loosely install the union bolt.
Tighten the 2 nuts and union bolt of the turbo oil pipe sub-assembly, and the 2 bolts.
- Torque:
- for nut:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
- for union bolt:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
- for bolt:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }
- HINT:
- Tighten the nut, union bolt and bolt in that order.
Install the manifold stay with the 2 bolts.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
- HINT:
- The manifold stay indented area must face the turbocharger sub-assembly.
w/ Intercooler:
Install a new gasket and the turbo oil inlet pipe sub-assembly with the 2 nuts, but only loosely install the nuts.

Text in Illustration *1
Gasket
*2
Turbo Oil Inlet Pipe Sub-assembly
*a
Narrow
*b
Wide


Outside
- NOTICE:
- The notch (wide part) of the gasket must face the engine.
Install a new gasket (labeled A) and the turbo oil inlet pipe sub-assembly with the 2 bolts, but only loosely install the bolts.

Text in Illustration *1
Gasket
*2
Turbo Oil Inlet Pipe Sub-assembly
*3
Union Bolt
*a
Craw


Turbo Oil Inlet Pipe Side
- NOTICE:
- The claws of the gasket must face the turbo oil inlet pipe sub-assembly.
Install a new gasket (labeled B) and the turbo oil inlet pipe sub-assembly with the union bolt, but only loosely install the union bolt.
Tighten the 2 nuts and union bolt of the turbo oil inlet pipe sub-assembly, and the 2 bolts.
- Torque:
- for nut:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
- for union bolt:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
- for bolt:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }
- HINT:
- Tighten the nut, union bolt and bolt in that order.
Install the 2 bolts and a new nut of the turbocharger stay in the order shown in the illustration.

- Torque:
- 38 N*m{ 387 kgf*cm , 28 ft.*lbf }
| 4. INSTALL TURBINE OUTLET ELBOW |
w/o Intercooler:
Temporarily install a new gasket and the turbine outlet elbow (with turbocharger stay) to the turbocharger sub-assembly with the 4 new nuts.
Temporarily install the turbine outlet elbow with the 2 bolts.
Tighten the 4 nuts of the turbine outlet elbow.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
Tighten the 2 bolts of the turbocharger stay.
- Torque:
- 38 N*m{ 387 kgf*cm , 28 ft.*lbf }
w/ Intercooler:
Install a new gasket and the turbine outlet elbow with the 3 new nuts.- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 5. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ Intercooler) |
Temporarily install the No. 1 exhaust manifold heat insulator with the bolt.
Tighten the bolt of the No. 1 turbo insulator, and the 2 bolts of the No. 1 exhaust manifold heat insulator.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }
| 6. INSTALL NO. 1 TURBO INSULATOR (w/ Intercooler) |
Temporarily install the No. 1 turbo insulator with the bolt.
| 7. INSTALL COMPRESSOR INLET ELBOW (w/ Intercooler) |
for Type B:
Connect the 2 No. 1 turbo water hoses to the No. 2 water by-pass pipe sub-assembly and the cylinder block sub-assembly, and slide the 4 clamps to secure the hoses.
for Type A:
Install the No. 12 water by-pass hose to the compressor inlet elbow, and slide the 2 clamps to secure the hose.
Install the No. 7 water by-pass hose to the compressor inlet elbow, slide the clamp to secure the hose.
Install a new gasket and the compressor inlet elbow with the 2 nuts.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
for Type A:
Connect the No. 13 water by-pass hose to the No. 2 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
Connect the No. 2 water by-pass hose to the compressor inlet elbow, and slide the clamp to secure the hose.
Connect the No. 1 turbo water hose to the cylinder block sub-assembly, and slide the clamp to secure the hose.
Connect the 2 connectors and attach the wire harness clamp.
| 8. INSTALL VENTILATION PIPE (w/ Intercooler) |
Install the ventilation pipe with the bolt.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
for Type A:
Connect the No. 12 water by-pass hose and No. 13 water by-pass hose to the ventilation pipe, and slide the 2 clamps to secure the hoses.
| 9. INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o Intercooler) |
Connect the pipe (with the 2 air hoses) and install the bolt.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Tighten the 2 clamps.
Connect the vacuum hose to the gas filter.
Connect the manifold absolute pressure sensor connector.
w/ No. 1 Engine Cover
Install the engine cover bracket with the 2 bolts.
- Torque:
- 18 N*m{ 184 kgf*cm , 13 ft.*lbf }
Attach the 4 claws to the pins of the engine cover bracket and install the No. 1 engine cover sub-assembly.
| 10. INSTALL VENTILATION HOSE HEAT INSULATOR (w/o Intercooler) |
Install the ventilation hose heat insulator with the 2 bolts.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }
| 11. INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler) |
| 12. INSTALL AIR CLEANER ASSEMBLY |
w/o Mass Air Flow Meter:
Connect the air cleaner hose.
Install the air cleaner assembly with the 2 bolts.
- Torque:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
Tighten the clamp.
Attach the clamp and connect the intake air temperature sensor connector.
Connect the ventilation hose to the cylinder head cover sub-assembly, and slide the clamp to secure the hose.
w/ Mass Air Flow Meter:
Connect the No. 1 air cleaner hose.
Install the air cleaner assembly with the 2 bolts.
- Torque:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
w/o Intercooler:
Connect the ventilation hose to the cylinder head cover sub-assembly, and slide the clamp to secure the hose.Connect the connector to the mass air flow meter.
Tighten the hose clamp.
| 13. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Using a vernier caliper, measure the free length of the compression spring.

- Minimum length:
- 40 mm (1.57 in.)
Install the front pipe to the pipe support.
Install a new gasket to the outlet pipe.

- NOTICE:
- Be careful with the installation direction of the gasket.
- Be careful with the installation direction of the gasket.
- Do not reuse the gasket.
- Do not reuse the gasket.
- To ensure a proper seal, do not use the front pipe to force the gasket onto the outlet pipe.
- To ensure a proper seal, do not use the front pipe to force the gasket onto the outlet pipe.
- HINT:
- Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and outlet pipe are properly fit.
Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.
- Torque:
- 43 N*m{ 438 kgf*cm , 32 ft.*lbf }
- CAUTION:
- Do not reuse the gasket.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 15. ADD ENGINE COOLANT (w/ Intercooler) |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.

- Standard Capacity:
Item
Specified Condition
for Automatic Transmission
11.1 liters (11.7 US qts, 9.8 Imp. qts)
for Manual Transmission
9.8 liters (10.4 US qts, 8.6 Imp. qts)
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Please contact your TOYOTA dealer for further details.
- Please contact your TOYOTA dealer for further details.
- NOTICE:
- Never use water as a substitute for engine coolant.
Press the radiator hose inlet and radiator hose outlet several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.

- Torque:
- 2.0 N*m{ 20 kgf*cm , 18 in.*lbf }
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the radiator hose inlet and radiator hose outlet several times by hand to bleed air.
- CAUTION:
- When pressing the radiator hoses:
- Wear protective gloves.
- Wear protective gloves.
- Be careful as the radiator hoses are hot.
- Be careful as the radiator hoses are hot.
- Keep your hands away from the radiator fan.
- Keep your hands away from the radiator fan.
Stop the engine and wait until the coolant cools down to ambient temperature.
- CAUTION:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
After the coolant cools down, check that the coolant level is at the F line.

If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 16. INSPECT FOR ENGINE COOLANT (w/ Intercooler) |
- NOTICE:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Fill the radiator with coolant and attach a radiator cap tester.

Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2 ,17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 17. INSPECT FOR ENGINE OIL LEAKS |
| 18. INSPECT ENGINE OIL LEVEL |
| 19. CHECK FOR EXHAUST LEAKS |
| 20. INSTALL FRONT FENDER APRON SEAL UPPER |
Install the front fender apron seal upper with the 5 clips.
| 21. INSTALL FRONT FENDER SEAL |
Install the front fender seal with the 5 clips.
| 22. INSTALL NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner) |
- Torque:
- 28 N*m{ 286 kgf*cm , 21 ft.*lbf }
| 23. INSTALL NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner) |
- Torque:
- 28 N*m{ 286 kgf*cm , 21 ft.*lbf }
