2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.

NOTICE:
When disconnecting the cable, systems need to be initialized after the cable is reconnected (Click here).


2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


3. REMOVE FRONT WHEEL RH

4. REMOVE FRONT FENDER APRON SEAL UPPER
  1. Remove the 5 clips and front fender apron seal upper.


5. REMOVE FRONT FENDER SEAL
  1. Remove the 5 clips and front fender seal.


6. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the front pipe from the outlet pipe and remove the gasket.

  1. Remove the front pipe from the pipe support.


7. REMOVE AIR CLEANER ASSEMBLY

  1. A099628E03
    Disconnect the MAF meter connector and detach the wire harness clamp.

  1. Loosen the hose clamp of the compressor inlet elbow.

  1. for Ventilation Hose Type:
    Disconnect the ventilation hose.

  1. Remove the 2 bolts and air cleaner.


8. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A135916
    Remove the 3 bolts, 2 nut and engine cover.


9. REMOVE INTERCOOLER ASSEMBLY

  1. A149802
    Detach the 2 clamps.

  1. Disconnect the vacuum hose from the manifold absolute pressure sensor.

  1. Disconnect the IAT sensor connector and manifold absolute diesel pressure sensor connector.

  1. A149933
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. A149934
    Loosen the 2 hose clamps of the No. 2 air hose.

  1. A135919
    Remove the 4 bolts and intercooler.


10. REMOVE COMPRESSOR INLET ELBOW

  1. A211832
    for Ventilation Pipe Type:
    Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe.

  1. A211833
    Detach the wire harness clamp.

  1. Remove the 2 nuts, inlet elbow and gasket.


11. REMOVE NO. 1 TURBO INSULATOR

  1. A211834
    Remove the 2 bolts and No. 1 turbo insulator.


12. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Remove the bolt and No. 1 exhaust manifold heat insulator.


13. REMOVE NO. 1 TURBO WATER HOSE

  1. A211835
    Remove the 2 No. 1 turbo water hoses.


14. REMOVE TURBINE OUTLET ELBOW

  1. A211836
    Remove the 3 nuts, turbine outlet elbow and gasket.


15. REMOVE TURBOCHARGER STAY

  1. A211837
    Remove the 2 bolts, nut and turbocharger stay.


16. REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

  1. A211838E01
    Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe and 3 gaskets.

    NOTICE:
    Do not loosen the nut labeled A.


17. REMOVE TURBOCHARGER SUB-ASSEMBLY

  1. A211839
    Remove the 3 nuts, turbocharger and gasket.


18. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

  1. A211906
    Remove the 2 nuts, bolt, No. 1 turbo water pipe and gasket.

← SYSTEM DESCRIPTION (from Aug 2013)REMOVAL (Aug 2012 – Jul 2013) →