2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE
  1. Remove the EGR cooler (Click here).


3. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD)
  1. Remove the 4 bolts and No. 1 engine under cover.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


5. DISCONNECT RADIATOR HOSE INLET

6. REMOVE FAN SHROUD

A151122
  1. Remove the 3 bolts and oil reservoir.

  1. Disconnect the No. 1 and No. 2 water by-pass hoses from the tank upper and lower.

  1. Remove the 2 bolts and radiator reservoir.

  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the drive belt (Click here).

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.


7. REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


8. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (for Cold Area Specification Vehicles)

  1. I034100E02
    Disconnect the connector.

  1. Remove the 2 bolts and viscous with magnet clutch heater assembly.


9. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)
  1. Remove the 4 bolts and No. 1 viscous heater bracket.


10. REMOVE GENERATOR ASSEMBLY

A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.


11. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A098937E01
    Remove the 4 bolts and V-ribbed belt tensioner.


12. REMOVE NO. 4 INJECTION PIPE

  1. A152275
    Remove the bolt and disconnect the injection pipe clamp.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. A152276E05
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


13. REMOVE VENTILATION PIPE

  1. A151170
    Remove the bolt and ventilation pipe.


14. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. G034844E02
    Disconnect the ventilation hose.

  1. Disconnect the 4 injector connectors.

  1. A060180E01
    Using a small screwdriver, remove the 4 nozzle holder seals by prying the portion between each nozzle holder seal and the cutout part of the cylinder head cover.

  1. G034877E01
    Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


15. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. A148169
    Remove the 6 bolts and timing belt cover.


16. REMOVE TIMING BELT

  1. A070549E02
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.

  1. A070550E01
    Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.

  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:
    A148170E01
    1. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    2. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.


17. REMOVE CAMSHAFT TIMING PULLEY

A060182E01
  1. Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.

    NOTICE:
    Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.

  1. Remove the camshaft timing pulley.


18. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nut and timing belt cover.


19. REMOVE CYLINDER BLOCK INSULATOR

  1. A149941
    Remove the cylinder block insulator form the head.


20. REMOVE WATER PUMP ASSEMBLY

  1. A225339
    Remove the 2 nuts, 5 bolts, water pump and gasket.

← COMPONENTS (from Aug 2012)REMOVAL (from Aug 2012) →