2014 Hilux · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Jun 2011


CLEAN CYLINDER HEAD SUB-ASSEMBLY

A059926E01
  1. Clean the cylinder head.

    1. Using a gasket scraper, remove all the gasket material from the cylinder block contact surface.

      NOTICE:
      Be careful not to scratch the cylinder block contact surface.

  1. A059164E01
    Using a valve guide bushing brush and solvent, clean all the guide bushes.

  1. A059924E01
    Using a soft brush and solvent, thoroughly clean the cylinder head.


INSPECT CYLINDER HEAD SUB-ASSEMBLY

A061553E01
  1. Inspect the cylinder head warpage.

    1. Using a precision straightedge and feeler gauge, measure the surfaces contacting the cylinder block and the manifolds for warpage.

      Maximum warpage:
      0.15 mm (0.0059 in.)

      If the warpage is greater than the maximum, replace the cylinder head.

  1. A059927E01
    Inspect the cylinder head for cracks.

    1. Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.
      If cracked, replace the cylinder head.


CLEAN INTAKE VALVE

A053867E01
  1. Using a gasket scraper, chip off any carbon from the valve head.

  1. Using a wire brush, thoroughly clean the valve.


INSPECT INTAKE VALVE

A053806E01
  1. Using a micrometer, measure the diameter of the valve stem.

    Standard valve stem diameter:
    5.970 to 5.985 mm (0.2350 to 0.2356 in.)

    If the diameter is not as specified, replace the valve.

  1. A053834E04
    Check the valve face angle.

    1. Grind the valve enough to remove pits and carbon.

    2. Check that the valve is ground to the correct valve face angle.

      Standard valve face angle:
      44.5°

      If the valve is worm, replace the valve.

  1. A053643E03
    Check the valve head margin thickness.

    Standard margin thickness:
    1.1 mm (0.043 in.)

    Minimum margin thickness:
    0.6 mm (0.024 in.)

    If the margin thickness is less than the minimum, replace the valve.

  1. A053642E03
    Check the valve overall length.

    Standard overall length:
    105.38 to 105.78 mm (4.1488 to 4.1646 in.)

    Minimum overall length:
    104.88 mm (4.1291 in.)

    If the overall length is less than the minimum, replace the valve.

  1. A053828E01
    Check the surface of the valve stem tip for wear.
    If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.

    NOTICE:
    Do not grind off more than the minimum.


CLEAN EXHAUST VALVE

A053867E01
  1. Using a gasket scraper, chip off any carbon from the valve head.

  1. Using a wire brush, thoroughly clean the valve.


INSPECT EXHAUST VALVE

A053806E01
  1. Using a micrometer, measure the diameter of the valve stem.

    Standard valve stem diameter:
    5.960 to 5.975 mm (0.2346 to 0.2352 in.)

    If the diameter is not as specified, replace the valve.

  1. A053834E04
    Check the valve face angle.

    1. Grind the valve enough to remove pits and carbon.

    2. Check that the valve is ground to the correct valve face angle.

      Standard valve face angle:
      44.5°

      If the valve face is worn, replace the valve.

  1. A053643E03
    Check the valve head margin thickness.

    Standard margin thickness:
    1.1 mm (0.043 in.)

    Minimum margin thickness:
    0.6 mm (0.024 in.)

    If the margin thickness is less than the minimum, replace the valve.

  1. A053642E03
    Check the valve overall length.

    Standard overall length:
    105.57 to 105.97 mm (4.1563 to 4.1720 in.)

    Minimum overall length:
    105.07 mm (4.1366 in.)

    If the overall length is less than the minimum, replace the valve.

  1. A053828E01
    Check the surface of the valve stem tip for wear.
    If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.

    NOTICE:
    Do not grind off more than the minimum.


INSPECT COMPRESSION SPRING

A053807E03
  1. Using a steel square, measure the deviation of the spring.

    Maximum deviation:
    2.0 mm (0.079 in.)

    If the deviation is greater than the maximum, replace the spring.

  1. A061556E01
    Using a vernier caliper, measure the free length of the spring.

    Standard free length:
    Blue mark
    None
    46.8 mm (1.843 in.)
    46.5 mm (1.831 in.)

    If the free length is not as specified, replace the spring.

  1. EM00281E01
    Using a spring tester, measure the tension of the valve spring at the specified installed length.

    Standard installed tension (at 33.1 mm (1.303 in.)):
    Blue mark
    None
    149.9 to 166.1 N (15.3 to 16.9 kgf, 33.7 to 37.3 lbf)
    150.2 to 165.8 N (15.3 to 16.9 kgf, 33.7 to 37.3 lbf)

    If the tension is not as specified, replace the spring.


INSPECT INTAKE VALVE GUIDE BUSH

A061557E01
  1. Using a caliper gauge, measure the inside diameter of the guide bush.

    Standard bush inside diameter:
    6.010 to 6.030 mm (0.2366 to 0.2374 in.)

    If the journal diameter is not as specified, check the oil clearance.

  1. Subtract the valve stem diameter measurement (see "INSPECT INTAKE VALVE" procedures above) from the guide bush inside diameter measurement.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)

    Maximum oil clearance:
    0.08 mm (0.0031 in.)

    If the clearance is greater than the maximum, replace the valve and guide bush.


INSPECT EXHAUST VALVE GUIDE BUSH

A061558E01
  1. Using a caliper gauge, measure the inside diameter of the guide bush.

    Standard bush inside diameter:
    6.010 to 6.030 mm (0.2366 to 0.2374 in.)

    If the journal diameter is not as specified, check the oil clearance.

  1. Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

    Standard oil clearance:
    0.035 to 0.070 mm (0.0014 to 0.0028 in.)

    Maximum oil clearance:
    0.10 mm (0.0039 in.)

    If the clearance is greater than the maximum, replace the valve and guide bush.


INSPECT INTAKE VALVE SEAT

A059929E02
  1. Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the seats.

  1. A059921E01
    Check the valve seating position.

    1. Apply a light coat of Prussian blue (or white lead) to the valve face.

    2. Lightly press the valve against the seat. Do not rotate valve.

  1. Check the valve face and seat for the following:

    1. If blue appears 360° around the face, the valve is concentric. If not, replace the valve.

    2. If blue appears 360° around the valve seat, the guide and face are concentric. If not, resurface the seat.

    3. Check that the seat contact is in the middle of the valve face with the width below.

      Standard width:
      1.2 to 1.6 mm (0.047 to 0.063 in.)


INSPECT EXHAUST VALVE SEAT

A058112E02
  1. Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the seats.

  1. A059920E01
    Check the valve seating position.

    1. Apply a light coat of Prussian blue (or white lead) to the valve face.

    2. Lightly press the valve against the seat. Do not rotate valve.

  1. Check the valve face and seat for the following:

    1. If blue appears 360° around the face, the valve is concentric. If not, replace the valve.

    2. If blue appears 360° around the valve seat, the guide and face are concentric. If not, resurface the seat.

    3. Check that the seat contact is in the middle of the valve face with the width below.

      Standard width:
      1.6 to 2.0 mm (0.063 to 0.079 in.)


INSPECT VALVE LIFTER

P016860E01
  1. Using a micrometer, measure the lifter diameter.

    Standard lifter diameter:
    30.966 to 30.976 mm (1.2191 to 1.2195 in.)

  1. A058115E01
    Using a caliper gauge, measure the lifter bore diameter of the cylinder head.

    Standard lifter bore diameter:
    31.000 to 31.021 mm (1.2205 to 1.2213 in.)

    If the lifter diameter is not as specified, check the oil clearance.

  1. Subtract the lifter diameter measurement from the lifter bore diameter measurement.

    Standard oil clearance:
    0.024 to 0.055 mm (0.0009 to 0.0022 in.)

    Maximum oil clearance:
    0.075 mm (0.0030 in.)

    If the oil clearance is greater than the maximum, replace the lifter. If necessary, replace the cylinder head.


INSPECT CYLINDER HEAD SET BOLT

A062121E01
  1. Using a vernier caliper, measure the minimum outside diameter of the compressed thread at the measuring point A.

    Standard outside diameter:
    11.8 to 12.0 mm (0.465 to 0.472 in.)

    Minimum outside diameter:
    11.6 mm (0.457 in.)

    If the outside diameter is less than the minimum, replace the bolt.


INSPECT CAMSHAFT

A059916E01
  1. Inspect the circle runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.0012 in.)

      If the circle runout is greater than the maximum, replace the camshaft.

  1. Inspect the cam lobe height.

    1. A059913E01
      Using a micrometer, measure the cam lobe height.

      Standard cam lobe height:
      46.830 to 46.930 mm (1.8437 to 1.8476 in.)

      Minimum cam lobe height:
      46.68 mm (1.8378 in.)

      If the cam lobe height is less than the minimum, replace the camshaft.

  1. A059914E01
    Inspect the journal diameter of the camshaft.

    1. Using a micrometer, measure the journal diameter of the camshaft for the camshaft bearing.

      Standard journal diameter:
      27.969 to 27.985 mm (1.1011 to 1.1018 in.)

      If the journal diameter is not as specified, check the oil clearance.

  1. A059905E01
    Check the oil clearance.

    1. Clean the bearing caps and journals.

    2. Check the bearings for flaking and scoring.
      If the bearings are damaged, replace the bearing caps and cylinder head as a set.

    3. Install the bearings to the bearing caps and cylinder head.

    4. Place the camshaft on the cylinder head.

    5. Lay a strip of Plastigage across each of the journals.

    6. A059909E01
      Install the bearing caps.

      NOTICE:
      Do not turn the camshaft.

    7. Remove the bearing caps.

    8. A059906E01
      Measure the Plastigage at its widest point.

      Standard oil clearance:
      0.025 to 0.062 mm (0.0010 to 0.0024 in.)

      Maximum oil clearance:
      0.10 mm (0.0039 in.)

      If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the bearing cap and cylinder head as a set.

    9. Completely remove the Plastigage.

    10. Remove the camshaft.

  1. A059910E01
    Check the thrust clearance.

    1. Install the camshaft.

    2. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

      Standard thrust clearance:
      0.035 to 0.185 mm (0.014 to 0.073 in.)

      Maximum thrust clearance:
      0.25 mm (0.0098 in.)

      If the thrust clearance is greater than the maximum, replace the camshaft. If necessary, replace the bearing cap and cylinder head as a set.

  1. A061825E01
    Using a dial indicator, measure the backlash.

    1. Install the 2 camshafts.

    2. Using a dial indicator, measure the backlash.

      Standard backlash:
      0.035 to 0.145 mm (0.0014 to 0.0057 in.)

      Maximum thrust clearance:
      0.189 mm (0.0074 in.)

      If the backlash is greater than the maximum, replace the 2 camshafts.

    3. Remove the 2 camshafts.


INSPECT NO. 2 CAMSHAFT

A059915E01
  1. Inspect the circle runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.0012 in.)

      If the circle runout is greater than the maximum, replace the camshaft.

  1. Inspect the cam lobe height.

    1. A059913E01
      Using a micrometer, measure the cam lobe height.

      Standard cam lobe height:
      46.870 to 46.970 mm (1.8453 to 1.8492 in.)

      Minimum cam lobe height:
      46.72 mm (1.8394 in.)

      If the cam lobe height is less than the minimum, replace the camshaft.

  1. A059914E01
    Inspect the journal diameter of the camshaft.

    1. Using a micrometer, measure the journal diameter of the camshaft for the camshaft bearing.

      Standard journal diameter:
      27.969 to 27.985 mm (1.1011 to 1.1018 in.)

      If the journal diameter is not as specified, check the oil clearance.

  1. A059907E02
    Check the oil clearance.

    1. Clean the bearing caps and journals.

    2. Check the bearings for flaking and scoring.
      If the bearings are damaged, replace the bearing caps and cylinder head.

    3. Install the bearings to the bearing caps and cylinder head.

    4. Place the camshaft on the cylinder head.

    5. Lay a strip of Plastigage across each of the journals.

    6. A059911E01
      Install the bearing caps.

      NOTICE:
      Do not turn the camshaft.

    7. Remove the bearing caps.

    8. A059908E02
      Measure the Plastigage at its widest point.

      Standard oil clearance:
      0.025 to 0.062 mm (0.0010 to 0.0024 in.)

      Maximum oil clearance:
      0.10 mm (0.0039 in.)

      If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the bearing cap and cylinder head as a set.

    9. Completely remove the Plastigage.

    10. Remove the camshaft.

  1. A059912E01
    Check the thrust clearance.

    1. Install the camshaft.

    2. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

      Standard thrust clearance:
      0.035 to 0.185 mm (0.0014 to 0.0073 in.)

      Maximum thrust clearance:
      0.25 mm (0.0098 in.)

      If the thrust clearance is greater than the maximum, replace the camshaft. If necessary, replace the bearing cap and cylinder head as a set.

← DISASSEMBLY (from Jun 2011)REPLACEMENT (from Jun 2011) →