REASSEMBLY
Removal / installation · Vehicles built from Jun 2011
- HINT:
- Thoroughly clean all parts to be assembled.
- Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
- Replace all gaskets and oil seals with new ones.
| 1.
INSTALL STUD BOLT |
 |
- HINT:
- If a stud bolt is deformed or its threads are damaged, replace it.
Install the stud bolts.
-
Torque:
- for stud bolt A and D:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- for stud bolt B:
- 7.0 N*m{
71 kgf*cm
, 62 in.*lbf
}
- for stud bolt C:
- 15 N*m{
153 kgf*cm
, 11 ft.*lbf
}
- for stud bolt E:
- 20 N*m{
204 kgf*cm
, 15 ft.*lbf
}


Text in Illustration
*1
|
Stud Bolt A
|
*2
|
Stud Bolt B
|
*3
|
Stud Bolt C
|
*4
|
Stud Bolt D
|
*5
|
Stud Bolt E
|
-
|
-
|
*a
|
Front Side
|
*b
|
Intake Manifold Side
|
*c
|
Cylinder Head Cover Side
|
*d
|
Exhaust Manifold Side
|
| 2.
INSTALL NO. 1 STRAIGHT SCREW PLUG |
 |
- HINT:
- If a No. 1 straight screw plug is corroded, replace it.
Apply adhesive to the end of each No. 1 straight screw plug.
- Adhesive:
- Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Using a 6 mm hexagon wrench, install the No. 1 straight screw plugs.
-
Torque:
- 25 N*m{
255 kgf*cm
, 18 ft.*lbf
}


Text in Illustration
*1
|
Adhesive
|
-
|
-
|
| 3.
INSTALL SEMICIRCULAR PLUG |
 |
Remove any old seal packing (FIPG material).
Apply seal packing to the semicircular plug as shown in the illustration.
- Seal packing:
- Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
- NOTICE:
- The semicircular plug must be installed within 3 minutes after applying the seal packing.
- Prevent seal packing from adhering to the camshaft thrust groove.
Install the semicircular plug to the cylinder head.


Text in Illustration
*1
|
Seal Packing
|
-
|
-
|
| 4.
INSTALL INTAKE VALVE STEM OIL SEAL |
 |
- Using SST, push in a new oil seal.
- SST
- 09201-41020
| 5.
INSTALL EXHAUST VALVE STEM OIL SEAL |
 |
Using SST, push in a new oil seal.
- SST
- 09201-41020
| 6.
INSTALL INTAKE VALVE |
 |
- Apply a sufficient coat of engine oil to the tip area of the valve shown in the illustration.
Text in Illustration
*a
|
30 mm (1.18 in.) or more
|
- Install the valve, spring seat, compression spring and spring retainer.
Using SST, compress the compression spring and install the 2 valve spring retainer locks to the valve stem.
- SST
- 09202-70020
09202-00020
- Using a plastic-faced hammer, lightly tap the valve stem tip to assure a proper fit.
- NOTICE:
- Be careful not to damage the valve stem tip.
| 7.
INSTALL EXHAUST VALVE |
 |
- Apply a sufficient coat of engine oil to the tip area of the valve shown in the illustration.
Text in Illustration
*a
|
30 mm (1.18 in.) or more
|
- Install the valve, spring seat, compression spring and spring retainer.
Using SST, compress the compression spring and install the 2 valve spring retainer locks to the valve stem.
- SST
- 09202-70020
09202-00020
- Using a plastic-faced hammer, lightly tap the valve stem tip to assure a proper fit.
- NOTICE:
- Be careful not to damage the valve stem tip.