2014 Hilux · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from Jun 2011


1. REPLACE INTAKE VALVE GUIDE BUSH
  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. A059922E01
    Using SST and a hammer, tap out the valve guide bush.
    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

  1. Select a new guide bush.

    New Guide Bush:
    Item
    Specified Condition
    Bush bore diameter
    10.985 to 11.006 mm (0.4325 to 0.4333 in.)
    11.035 to 11.056 mm (0.4344 to 0.4353 in.)
    Bush to be used
    STD
    O/S 0.05

    If the bush bore diameter of the cylinder head is more than 11.006 mm (0.4333 in.), machine the bush bore diameter to between 11.035 and 11.056 mm (0.4344 and 0.4353 in.).
    If the bush bore diameter of the cylinder head is more than 11.056 mm (0.4353 in.), replace the cylinder head.

  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. A061560E01
    Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

    Standard protrusion height (H):
    10.3 to 10.7 mm (0.406 to 0.421 in.)

  1. A059166E02
    Using a sharp 6.0 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

    Standard clearance:
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)

    Text in Illustration 
    *1
    Sharp 6.0 mm Reamer


2. REPLACE EXHAUST VALVE GUIDE BUSH
  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. A059923E01
    Using SST and a hammer, tap out the valve guide bush.
    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

  1. Select a new guide bush.

    New Guide Bush:
    Item
    Specified Condition
    Bush bore diameter
    10.985 to 11.006 mm (0.4325 to 0.4333 in.)
    11.035 to 11.056 mm (0.4344 to 0.4353 in.)
    Bush to be used
    STD
    O/S 0.05

    If the bush bore diameter of the cylinder head is more than 11.006 mm (0.4333 in.), machine the bush bore diameter to between 11.035 and 11.056 mm (0.4344 and 0.4353 in.).
    If the bush bore diameter of the cylinder head is more than 11.056 mm (0.4353 in.), replace the cylinder head.

  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. A061559E01
    Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

    Standard protrusion height (H):
    10.3 to 10.7 mm (0.406 to 0.421 in.)

  1. A059170E02
    Using a sharp 6.0 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

    Standard clearance:
    0.035 to 0.070 mm (0.0014 to 0.0028 in.)

    Text in Illustration 
    *1
    Sharp 6.0 mm Reamer


3. REPLACE RING PIN

HINT:
It is not necessary to remove the ring pin unless it is being replaced.

  1. Remove the ring pin.

  1. Using a plastic-faced hammer, tap in a new ring pin until the pin stops.

    Standard protrusion:
    Less than 5 mm (0.197 in.)


    A200441E03
    Text in Illustration 
    *a
    Less than 5 mm (0.197 in.)
    -
    -

← INSPECTION (from Jun 2011)REASSEMBLY (from Jun 2011) →