INSPECTION
Inspection · Vehicles built from Jun 2011
| INSPECT BACKLASH OF OIL PUMP GEAR TO CRANKSHAFT TIMING GEAR |
![]() ![]() |
Using a dial indicator, measure the backlash.
- Standard gear backlash:
- 0.02 to 0.15 mm (0.0008 to 0.0060 in.)
- Maximum gear backlash:
- 0.20 mm (0.0079 in.)
| INSPECT NO. 1 IDLE GEAR THRUST CLEARANCE |
![]() ![]() |
Using a dial indicator, measure the thrust clearance.
- Standard thrust clearance:
- 0.06 to 0.11 mm (0.0024 to 0.0043 in.)
- Maximum thrust clearance:
- 0.30 mm (0.0118 in.)
| INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO NO. 1 IDLE GEAR |
![]() ![]() |
Install the idle gear.
Using a dial indicator, measure the backlash.
- Standard gear backlash:
- 0.02 to 0.15 mm (0.0008 to 0.0060 in.)
- Maximum gear backlash:
- 0.20 mm (0.0079 in.)
Remove the idle gear.
| INSPECT BACKLASH OF OIL PUMP GEAR TO NO. 1 BALANCE SHAFT |
![]() ![]() |
Using a dial indicator, measure the backlash.
- Standard gear backlash:
- 0.02 to 0.15 mm (0.0008 to 0.0060 in.)
- Maximum gear backlash:
- 0.20 mm (0.0079 in.)
| INSPECT BACKLASH OF SUPPLY PUMP GEAR TO NO. 2 BALANCE SHAFT |
![]() ![]() |
Install the supply pump with the 2 nuts.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 in.*lbf }
Using SST, install the supply pump gear with the nut.
- SST
- 09960-10010
(09962-01000, 09963-01000)
- Torque:
- 64 N*m{ 650 kgf*cm , 47 in.*lbf }
Using a dial indicator, measure the backlash.

- Standard gear backlash:
- 0.02 to 0.15 mm (0.0008 to 0.0060 in.)
- Maximum gear backlash:
- 0.20 mm (0.0079 in.)
| INSPECT BACKLASH OF SUPPLY PUMP GEAR TO NO. 1 IDLE GEAR |
![]() ![]() |
Install the idle gear without sub gears.
Using a dial indicator, measure the backlash.
- Standard gear backlash:
- 0.02 to 0.15 mm (0.0008 to 0.0060 in.)
- Maximum gear backlash:
- 0.20 mm (0.0079 in.)
Using SST, remove the nut and supply pump gear.
- SST
- 09960-10010
(09962-01000, 09963-01000)
Remove the 2 nuts and supply pump.
Remove the idle gear.
| INSPECT NO. 1 IDLE GEAR OIL CLEARANCE |
![]() ![]() |
Using a cylinder gauge, measure the inside diameter of the idle gear.
- Standard idle gear inside diameter:
- 44.000 to 44.025 mm (1.7323 to 1.7333 in.)
Using a micrometer, measure the diameter of the idle gear shaft.

- Standard idle gear shaft diameter:
- 43.955 to 43.990 mm (1.7305 to 1.7319 in.)
Subtract the idle gear shaft diameter measurement from the idle gear inside diameter measurement.
- Standard oil clearance:
- 0.010 to 0.070 mm (0.0004 to 0.0028 in.)
- Maximum oil clearance:
- 0.20 mm (0.0079 in.)
| INSPECT NO. 1 BALANCE SHAFT SUB-ASSEMBLY |
![]() ![]() |
Using a dial indicator, measure the thrust clearance by moving the balance shaft back and forth.
- Standard thrust clearance:
- 0.065 to 0.140 mm (0.0026 to 0.0055 in.)
- Maximum thrust clearance:
- 0.25 mm (0.0098 in.)
- HINT:
- After replacement, if the thrust clearance is still greater than the maximum, replace the balance shaft.
| INSPECT NO. 2 BALANCE SHAFT SUB-ASSEMBLY |
![]() ![]() |
Using a dial indicator, measure the thrust clearance by moving the balance shaft back and forth.
- Standard thrust clearance:
- 0.065 to 0.140 mm (0.0026 to 0.0055 in.)
- Maximum thrust clearance:
- 0.25 mm (0.0098 in.)
- HINT:
- After replacement, if the thrust clearance is still greater than the maximum, replace the balance shaft.
| INSPECT CYLINDER HEAD SET BOLT |
![]() ![]() |
Using a vernier caliper, measure the minimum outside diameter of the compressed thread at the measuring point A.
- Standard outside diameter:
- 11.8 to 12.0 mm (0.465 to 0.472 in.)
- Minimum outside diameter:
- 11.6 mm (0.457 in.)
| INSPECT INJECTION GEAR |
Check that bearing is not rough or worn.
If necessary, replace the injection gear.
| INSPECT CYLINDER BLOCK OIL ORIFICE |
Check the oil orifice for damage or clogging.
If necessary, replace the oil orifice.
| INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() ![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
- Standard thrust clearance:
- 0.100 to 0.300 mm (0.0039 to 0.0118 in.)
- Maximum thrust clearance:
- 0.40 mm (0.0157 in.)
| INSPECT CONNECTING ROD OIL CLEARANCE |
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches.
If the crank pin or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
Lay a strip of Plastigage across the crank pin.

Install the connecting rod cap with the 2 bolts.

- NOTICE:
- Do not turn the crankshaft.
Check the matchmarks on the connecting rod and cap to ensure correct reassembly.

Remove the 2 bolts, connecting rod cap and lower bearing.
Measure the Plastigage at its widest point.



- Standard oil clearance:
STD
U/S 0.25, U/S 0.50
0.036 to 0.054 mm (0.0014 to 0.0021 in.)
0.037 to 0.077 mm (0.0015 to 0.0030 in.)
- Maximum oil clearance:
- 0.10 mm (0.0039 in.)
- HINT:
- If using a standard bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the crankshaft and connecting rod, then selecting the bearing with the same number as the total. There are 5 sizes of standard bearings, marked 2, 3, 4, 5 and 6.
- Bearing size:
Item
Number Mark
Connecting rod cap
1
2
3
Crankshaft
1
2
3
1
2
3
1
2
3
Use bearing
2
3
4
3
4
5
4
5
6
Connecting rod cap "3" + Crankshaft "1" =
Total number 4 (Use bearing "4")- Reference:
- Standard connecting rod big end inside diameter:
Mark
Diameter
1
62.014 to 62.020 mm (2.4415 to 2.4417 in.)
2
62.020 to 62.026 mm (2.4417 to 2.4420 in.)
3
62.026 to 62.032 mm (2.4420 to 2.4422 in.)
- Standard crankshaft pin diameter:
Mark
Diameter
1
58.994 to 59.000 mm (2.3226 to 2.3228 in.)
2
58.988 to 58.994 mm (2.3224 to 2.3226 in.)
3
58.982 to 58.988 mm (2.3221 to 2.3224 in.)
- Standard sized bearing center wall thickness:
Mark
Diameter
2
1.486 to 1.489 mm (0.0585 to 0.0586 in.)
3
1.489 to 1.492 mm (0.0586 to 0.0587 in.)
4
1.492 to 1.495 mm (0.0587 to 0.0589 in.)
5
1.495 to 1.498 mm (0.0589 to 0.0590 in.)
6
1.498 to 1.501 mm (0.0590 to 0.0591 in.)
Completely remove the Plastigage.
| INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() ![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
- Standard thrust clearance:
- 0.040 to 0.240 mm (0.0016 to 0.0094 in.)
- Maximum thrust clearance:
- 0.30 mm (0.0118 in.)
- Standard thrust washer thickness:
STD
2.430 to 2.480 mm (0.0957 to 0.0976 in.)
O/S 0.125
2.555 to 2.605 mm (0.1006 to 0.1026 in.)
O/S 0.250
2.680 to 2.730 mm (0.1055 to 0.1074 in.)
| INSPECT CRANKSHAFT OIL CLEARANCE |
Clean each main journal and bearing.
Check each crankshaft journal and bearing for pitting and scratches.
If the journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
Place the crankshaft on the cylinder block.
Lay a strip of Plastigage across each journal.

Install the 5 crankshaft bearing caps with the 10 bolts.

- NOTICE:
- Do not turn the crankshaft.
Remove the 10 bolts and 5 crankshaft bearing caps.
Measure the Plastigage at its widest point.



- Standard oil clearance:
STD
0.030 to 0.048 mm (0.0012 to 0.0019 in.)
O/S 0.25, O/S 0.50
0.037 to 0.077 mm (0.0015 to 0.0030 in.)
- Maximum clearance:
- 0.10 mm (0.0039 in.)
- HINT:
- If replacing the cylinder block sub-assembly, the bearing standard oil clearance will be within standard value.
- Standard oil clearance:
- 0.030 to 0.048 mm (0.0012 to 0.0019 in.)
- HINT:
- If using a standard bearing, replace it with one having the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then selecting the bearing with the same number as the total. There are 5 sizes of standard bearings, marked 2, 3, 4, 5 and 6.
- Bearing size:
Item
Number Mark
Cylinder block
1
2
3
Crankshaft
1
2
3
1
2
3
1
2
3
Use bearing
2
3
4
3
4
5
4
5
6
Cylinder block "2" + crankshaft "1"= Total number 3 (Use bearing "3")- Reference:
- Standard cylinder block main journal bore diameter:
Mark
Diameter
1
75.000 to 75.006 mm (2.9528 to 2.9530 in.)
2
75.006 to 75.012 mm (2.9530 to 2.9532 in.)
3
75.012 to 75. 018 mm (2.9532 to 2.9535 in.)
- Standard crankshaft journal diameter:
Mark
Diameter
1
69.994 to 70.000 mm (2.75566 to 2.75590 in.)
2
69.988 to 69.994 mm (2.75543 to 2.75566 in.)
3
69.982 to 69.988 mm (2.75519 to 2.75543 in.)
- Standard sized bearing center wall thickness:
Mark
Diameter
2
2.482 to 2.485 mm (0.0977 to 0.0978 in.)
3
2.485 to 2.488 mm (0.0978 to 0.0980 in.)
4
2.488 to 2.491 mm (0.0980 to 0.0981 in.)
5
2.491 to 2.494 mm (0.0981 to 0.0982 in.)
6
2.494 to 2.497 mm (0.0982 to 0.0983 in.)
Completely remove the Plastigage.
| INSPECT OIL CHECK VALVE SUB-ASSEMBLY |
![]() ![]() |
Push the valve with a wooden stick to check if it is stuck.
If stuck, replace the check valve.
| INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY |
Check the oil nozzles for damage or clogging.
If necessary, replace the oil nozzle.
| CLEAN CYLINDER BLOCK SUB-ASSEMBLY |
![]() ![]() |
Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.
Using a soft brush and solvent, thoroughly clean the cylinder block.
| INSPECT CYLINDER BLOCK SUB-ASSEMBLY |
![]() ![]() |
Inspect for flatness.
Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head cap for warpage.
- Maximum warpage:
- 0.10 mm (0.0039 in.)
Visually check the cylinder for vertical scratches.

If deep scratches are present, rebore all 4 cylinders. If necessary, replace the cylinder block.
Inspect the cylinder bore diameter.

- HINT:
- There are 3 sizes of the standard cylinder bore diameter, marked 1, 2 and 3 accordingly. The mark is stamped on the lower left rear of the cylinder block.
Using a cylinder gauge, measure the cylinder bore diameter at positions A, B and C in the thrust and axial directions.

- Standard diameter:
Mark 1
Mark 2
Mark 3
96.000 to 96.010 mm (3.7795 to 3.7799 in.)
96.010 to 96.020 mm (3.7799 to 3.7803 in.)
96.020 to 96.030 mm (3.7803 to 3.7807 in.)
- Maximum diameter:
STD
O/S 0.50
O/S 0.75
O/S 1.00
96.23 mm (3.7886 in.)
96.73 mm (3.8083 in.)
96.98 mm (3.8181 in.)
97.23 mm (3.8279 in.)
Remove the cylinder ridge.

If the wear is less than 0.2 mm (0.008 in.), using a ridge reamer, grind the top of the cylinder.
| CLEAN PISTON |
Using a groove cleaning tool or broken ring, clean the piston ring grooves.

Using solvent and a brush, thoroughly clean the piston.

- NOTICE:
- Do not use a wire brush.
| INSPECT PISTON |
![]() ![]() |
- HINT:
- When replacing the piston sub-assembly (w/ pin) with a supply part, there are a number of piston diameter sizes to choose from, but there is only one size of piston pin diameter.
Inspect the piston oil clearance.
- HINT:
- There are 3 sizes of the standard piston diameter, marked "1", "2" and "3" accordingly. The mark is stamped on the piston top.
Using a micrometer, measure the piston diameter at right angles to the piston center line, the indicated distance from the piston head.
- Standard distance:
- 63.63 mm (2.5051 in.)
- Standard piston diameter:
Piston
Mark
Diameter
STD
Mark 1
95.92 to 95.93 mm (3.77637 to 3.77676 in.)
STD
Mark 2
95.93 to 95.94 mm (3.77676 to 3.77715 in.)
STD
Mark 3
95.94 to 95.95 mm (3.77716 to 3.77755 in.)
O/S 0.50
-
96.42 to 96.70 mm (3.7960 to 3.8070 in.)
O/S 0.75
-
96.67 to 96.95 mm (3.8058 to 3.8169 in.)
O/S 1.00
-
96.92 to 97.20 mm (3.8157 to 3.8267 in.)
Measure the cylinder bore diameter in the thrust directions.
Subtract the piston diameter measurement from the cylinder bore diameter measurement.

- Standard oil clearance:
- 0.070 to 0.090 mm (0.0028 to 0.0035 in.)
- Maximum oil clearance:
- 0.14 mm (0.0055 in.)
If necessary, replace the cylinder block.- HINT:
- Use a piston with the same number mark as the cylinder diameter marked on the cylinder block.
Using a micrometer, measure the piston pin diameter.

- Standard piston pin diameter:
Size Mark
Diameter
A
33.996 to 34.000 mm (1.3384 to 1.3386 in.)
B
34.000 to 34.004 mm (1.3386 to 1.3387 in.)
C
34.004 to 34.008 mm (1.3387 to 1.3389 in.)
Inspect the piston pin fit.

At 80°C (176°F), check that the piston pin can be pushed into the piston pin hole with your thumb.
If the pin can be installed at a lower temperature, replace the piston and pin as a set.
| INSPECT PISTON RING SET |
![]() ![]() |
Inspect the piston ring groove clearance.
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
- Standard groove clearance:
Item
Specified Condition
No. 2 Piston Ring
w/ EGR System
0.090 to 0.130 mm (0.0036 to 0.0051 in.)
w/o EGR System
0.090 to 0.135 mm (0.0036 to 0.0053 in.)
Oil Ring
0.030 to 0.075 mm (0.0012 to 0.0027 in.)
- Maximum groove clearance:
- 0.20 mm (0.0079 in.)
Inspect the piston ring end gap.

Insert the piston ring into the cylinder bore.
Using a piston, push the piston ring a little beyond the bottom of the ring travel and 120 mm (4.72 in.) from the top of the cylinder block.
Using a feeler gauge, measure the end gap.

- Standard end gap:
Item
Specified Condition
No. 1
0.27 to 0.39 mm (0.0106 to 0.0154 in.)
No. 2
w/ EGR System
0.47 to 0.57 mm (0.0185 to 0.0224 in.)
w/o EGR System
0.55 to 0.70 mm (0.0217 to 0.0276 in.)
Oil
0.20 to 0.40 mm (0.0079 to 0.0157 in.)
- Maximum end gap:
Item
Specified Condition
No. 1
0.85 mm (0.0335 in.)
No. 2
1.07 mm (0.0421 in.)
Oil
0.77 mm (0.0303 in.)
If the end gap is greater than the maximum, even with a new piston ring, rebore all 4 cylinders or replace the cylinder block.
| INSPECT CONNECTING ROD SUB-ASSEMBLY |
![]() ![]() |
Using a rod aligner and feeler gauge, check the connecting rod alignment.
Check for bend.
- Maximum bend:
- 0.03 mm (0.0012 in.) per 100 mm (3.94 in.)
Check if the rod is twisted.

- Maximum twist:
- 0.15 mm (0.0059 in.) per 100 mm (3.94 in.)
| INSPECT PISTON PIN OIL CLEARANCE |
![]() ![]() |
Inspect the piston pin oil clearance.
Using a caliper gauge, measure the inside diameter of the connecting rod bush.
- Standard bush inside diameter:
Size Mark
Diameter
A
34.012 to 34.016 mm (1.3390 to 1.3392 in.)
B
34.016 to 34.020 mm (1.3392 to 1.3394 in.)
C
34.020 to 34.024 mm (1.3394 to 1.3395 in.)
Subtract the piston pin diameter measurement from the bush inside diameter measurement.
- Standard oil clearance:
- 0.012 to 0.020 mm (0.0005 to 0.0008 in.)
- Maximum oil clearance:
- 0.03 mm (0.0012 in.)
If necessary, replace the piston and piston pin with a new piston and pin set.
| INSPECT CONNECTING ROD BOLT |
![]() ![]() |
Using a vernier caliper, measure the tension portion of the connecting rod bolt.
- Standard diameter:
- 8.500 to 8.600 mm (0.3346 to 0.3385 in.)
- Minimum diameter:
- 8.30 mm (0.3268 in.)
| INSPECT NO. 1 BALANCE SHAFT SUB-ASSEMBLY |
![]() ![]() |
Using a cylinder gauge, measure the inside diameter of the balance shaft bearing.
- Bearing inside diameter:
No. 1
No. 2
No. 3
42.000 to 42.020 mm (1.6535 to 1.6543 in.)
41.000 to 41.020 mm (1.6142 to 1.6150 in.)
32.000 to 32.020 mm (1.2598 to 1.2606 in.)
Using a micrometer, measure the outside diameter of the balance shaft main journals.

- Main journal diameter:
No. 1
No. 2
No. 3
41.941 to 41.960 mm (1.6512 to 1.6520 in.)
40.931 to 40.950 mm (1.6115 to 1.6122 in.)
31.941 to 31.960 mm (1.2575 to 1.2583 in.)
Subtract the outside diameter of the balance shaft main journal from the inside diameter of the balance shaft bearing.
- Standard clearance:
No. 1
No. 2
No. 3
0.040 to 0.079 mm (0.0016 to 0.0031 in.)
0.050 to 0.089 mm (0.0020 to 0.0035 in.)
0.040 to 0.079 mm (0.0016 to 0.0031 in.)
- Maximum oil clearance:
No. 1
No. 2
No. 3
0.18 mm (0.0071 in.)
0.19 mm (0.0075 in.)
0.18 mm (0.0071 in.)
| INSPECT NO. 2 BALANCE SHAFT SUB-ASSEMBLY |
![]() ![]() |
Using a cylinder gauge, measure the inside diameter of the balance shaft bearing.
- Bearing inside diameter:
No. 1
No. 2
No. 3
42.000 to 42.020 mm (1.6535 to 1.6543 in.)
41.000 to 41.020 mm (1.6142 to 1.6150 in.)
32.000 to 32.020 mm (1.2598 to 1.2606 in.)
Using a micrometer, measure the outside diameter of the balance shaft main journals.

- Main journal diameter:
No. 1
No. 2
No. 3
41.941 to 41.960 mm (1.6512 to 1.6520 in.)
40.931 to 40.950 mm (1.6115 to 1.6122 in.)
31.941 to 31.960 mm (1.2575 to 1.2583 in.)
Subtract the outside diameter to the balance shaft main journal from the inside diameter to the balance shaft bearing.
- Standard clearance:
No. 1
No. 2
No. 3
0.040 to 0.079 mm (0.0016 to 0.0031 in.)
0.050 to 0.089 mm (0.0020 to 0.0035 in.)
0.040 to 0.079 mm (0.0016 to 0.0031 in.)
- Maximum oil clearance:
No. 1
No. 2
No. 3
0.18 mm (0.0071 in.)
0.19 mm (0.0075 in.)
0.18 mm (0.0071 in.)
| INSPECT CRANKSHAFT |
![]() ![]() |
Inspect for circle runout.
Place the crankshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
- Maximum circle runout:
- 0.03 mm (0.0012 in.)
Inspect the main journals and crank pins.

Using a micrometer, measure the diameter of each main journal and crank pin.
- Standard main journal diameter:
Mark 1
Mark 2
Mark 3
69.994 to 70.000 mm (2.75566 to 2.75590 in.)
69.988 to 69.994 mm (2.75543 to 2.75566 in.)
69.982 to 69.988 mm (2.75519 to 2.75543 in.)
- Standard crank pin diameter:
Mark 1
Mark 2
Mark 3
58.994 to 59.000 mm (2.32259to 2.32283 in.)
58.988 to 59.994 mm (2.32236 to 2.32259 in.)
58.982 to 58.988 mm (2.32212 to 2.32239 in.)
Check each main journal and crank pin for taper and out-of-round as shown.
- Maximum taper and out-of-round:
- 0.020 mm (0.0008 in.)
If necessary, grind and hone the main journals and/or crank pins.
Grind and hone the main journals and/or crank pins to the finished undersized diameter.
Install new main journal and/or crankshaft pin undersized bearing.
| INSPECT CRANKSHAFT BEARING CAP BOLT |
![]() ![]() |
Using a vernier caliper, measure the minimum diameter of the elongated thread at the measuring point.
- Standard diameter:
- 13.500 to 14.000 mm (0.5315 to 0.5512 in.)
- Minimum diameter:
- 12.60 mm (0.4961 in.)
























