REMOVAL
Removal / installation · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for RHD and LHD vehicles.
| 1. REMOVE FRONT SEAT ASSEMBLY LH |
w/ Front Seat Side Airbag:
(Click here)
for Separate Seat Type:
(Click here)
| 2. REMOVE FRONT SEAT ASSEMBLY RH |
w/ Front Seat Side Airbag:
- HINT:
- Use the same procedure described for the LH side.
for Separate Seat Type:
- HINT:
- Use the same procedure described for the LH side.
for Bench Seat Type:
(Click here)
| 3. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box) |
| 4. REMOVE UPPER BACK PANEL GARNISH |
![]() ![]() |
Detach the 4 claws, 4 guides and 5 clips and remove the upper back panel garnish.
| 5. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() ![]() |
Put protective tape around the front door scuff plate.
Text in Illustration *1
Protective Tape
Using a moulding remover, detach the 4 clips and 8 claws and remove the front door scuff plate.
| 6. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD) |
- HINT:
- Use the same procedure described for the LH side.
| 7. REMOVE COWL SIDE TRIM BOARD LH (for LHD) |
![]() ![]() |
Remove the part of the front door opening trim attached to the cowl side trim board.
Remove the clip.
Detach the 2 clips and remove the cowl side trim board.
| 8. REMOVE COWL SIDE TRIM BOARD RH (for RHD) |
- HINT:
- Use the same procedure described for the LH side.
| 9. REMOVE LOWER QUARTER TRIM PANEL LH |
![]() ![]() |
Remove the bolt and disconnect the front seat outer belt floor anchor.
Remove the part of the front door opening trim attached to the lower quarter trim panel.

Detach the claw, 3 clips and 2 guides and remove the lower quarter trim panel.
| 10. REMOVE FRONT FLOOR CARPET ASSEMBLY |
Partially remove the floor carpet.
- HINT:
- It is not necessary to fully remove the floor carpet. Partially remove it so that the lock control cable can be removed in a later step.
| 11. REMOVE REAR NO. 1 WHEEL OPENING EXTENSION SUB-ASSEMBLY LH (w/ Over Fender) |
w/ Mudguard:
Put protective tape around the No. 1 rear wheel opening extension.

Text in Illustration *1
Protective Tape
Remove the 5 screws.
w/o Mudguard:
Put protective tape around the No. 1 rear wheel opening extension.

Text in Illustration *1
Protective Tape
Remove the 8 screws.
Detach the 11 clips and remove the No. 1 rear wheel opening extension.

Remove the 11 clips from the vehicle body.
| 12. REMOVE REAR WHEEL HOUSE LINER LH |
Partially remove the rear wheel house liner.
- HINT:
- It is not necessary to fully remove the liner. Partially remove it so that the lock control cable can be removed in a later step.
| 13. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
for LHD:
Remove the fuel lid lock open lever.
Remove the grommet from the vehicle body.
Detach the cable from the clamps shown in the illustration.


Text in Illustration *1
Fuel Lid Lock Open Lever
*2
Grommet
Turn the fuel filler opening lid lock retainer counterclockwise and remove the cable from the fuel filler opening lid lock retainer.

for RHD:
Remove the fuel lid lock open lever.
Remove the grommet from the vehicle body.
Detach the cable from the clamps shown in the illustration.


Text in Illustration *1
Fuel Lid Lock Open Lever
*2
Grommet
Turn the fuel filler opening lid lock retainer counterclockwise and remove the cable from the fuel filler opening lid lock retainer.

| 14. REMOVE FUEL FILLER OPENING LID LOCK RETAINER |
![]() ![]() |
Turn the fuel filler opening lid lock retainer clockwise and remove the fuel filler opening lid lock retainer as shown in the illustration.





