2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE FRONT SEAT ASSEMBLY LH
  1. w/ Front Seat Side Airbag:
    (Click here)

  1. for Separate Seat Type:
    (Click here)


2. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


3. REMOVE CONSOLE BOX ASSEMBLY
(Click here)

4. REMOVE REAR SEAT CUSHION ASSEMBLY LH (w/ Seat Cushion)

  1. B288340
    Operate the rear seat cushion lock hook release lever and pull up the rear seat cushion assembly LH to detach the hook.
    Text in Illustration 
    V100135
    Pull Up
    V100136
    Release

  1. B288341
    Detach the 2 hooks and rear seat cushion assembly LH.


5. REMOVE REAR SEAT CUSHION ASSEMBLY RH (w/ Seat Cushion)

HINT:
Use the same procedures described for the LH side.


6. REMOVE UPPER BACK PANEL GARNISH

B276964
  1. Detach the 4 claws and 5 clips and remove the upper back panel garnish.


7. REMOVE REAR SEATBACK ASSEMBLY

  1. B276915
    Remove the 2 bolts.

  1. Lift up the rear seatback assembly in the direction indicated by the arrow to detach the 2 hooks from the vehicle body. Then remove the rear seatback assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


8. REMOVE LOWER BACK PANEL GARNISH

B276965
  1. Detach the 6 claws, 2 guides and 5 clips and remove the lower back panel garnish.


9. REMOVE FRONT DOOR SCUFF PLATE LH

B276994E01
  1. Put protective tape around the front door scuff plate.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 4 clips and 8 claws and remove the front door scuff plate.


10. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure described for the LH side.


11. REMOVE COWL SIDE TRIM BOARD LH (for LHD)

B277609
  1. Remove the part of the front door opening trim attached to the cowl side trim board.

  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.


12. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

HINT:
Use the same procedure described for the LH side.


13. REMOVE QUARTER INSIDE TRIM BOARD LH

B276966
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.

  1. B276968
    Remove the part of the front door opening trim attached to the quarter inside trim board.

  1. Detach the 4 claws, 3 guides and 7 clips and remove the quarter inside trim board.


14. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Partially remove the floor carpet.

    HINT:
    It is not necessary to fully remove the floor carpet. Partially remove it so that the lock control cable can be removed in a later step.


15. REMOVE REAR NO. 1 WHEEL OPENING EXTENSION SUB-ASSEMBLY LH (w/ Over Fender)

  1. w/ Mudguard:

    1. B277559E01
      Put protective tape around the No. 1 rear wheel opening extension.
      Text in Illustration 
      *1
      Protective Tape

    2. Remove the 5 screws.

  1. w/o Mudguard:

    1. B291253E01
      Put protective tape around the No. 1 rear wheel opening extension.
      Text in Illustration 
      *1
      Protective Tape

    2. Remove the 8 screws.

  1. B277560
    Detach the 11 clips and remove the No. 1 rear wheel opening extension.

  1. Remove the 11 clips from the vehicle body.


16. REMOVE REAR WHEEL HOUSE LINER LH
  1. Partially remove the liner.

    HINT:
    It is not necessary to fully remove the liner. Partially remove it so that the lock control cable can be removed in a later step.


17. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

  1. for LHD:

    1. Remove the fuel lid lock open lever.

    2. Remove the grommet from the vehicle body.

    3. Detach the cable from the clamps shown in the illustration.

      B288687E01

      Text in Illustration 
      *1
      Fuel Lid Lock Open Lever
      *2
      Grommet

    4. B277114
      Turn the fuel filler opening lid lock retainer counterclockwise and remove the fuel lid lock control cable from the fuel filler opening lid lock retainer.

  1. for RHD:

    1. Remove the fuel lid lock open lever.

    2. Remove the grommet from the vehicle body.

    3. Detach the cable from the clamps shown in the illustration.

      B277113E01

      Text in Illustration 
      *1
      Fuel Lid Lock Open Lever
      *2
      Grommet

    4. B277114
      Turn the fuel filler opening lid lock retainer counterclockwise and remove the fuel lid lock control cable from the fuel filler opening lid lock retainer.


18. REMOVE FUEL FILLER OPENING LID LOCK RETAINER

B277116
  1. Turn the fuel filler opening lid lock retainer clockwise and remove the fuel filler opening lid lock retainer as shown in the illustration.

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →