2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)
  1. Remove the 4 bolts and No. 1 engine under cover.


3. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)
  1. Remove the 2 bolts and No. 2 engine under cover.


4. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

A111789
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the pipe together with the 2 air hoses.


5. REMOVE MANIFOLD STAY

  1. w/ EGR Cooler:

    1. Disconnect the 2 VSV connector and 3 vacuum hoses.

    2. A148131
      Remove the 2 bolts and manifold stay.

  1. w/o EGR Cooler:

    1. A099622E01
      Remove the 2 bolts and manifold stay.


6. REMOVE OIL FILTER SUB-ASSEMBLY

B011502E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the drain oil container beneath the drain hose to collect the oil from the oil filter.


7. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A098967E05
    Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.


8. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A098893E01
    Remove the 2 bolts.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. A231804E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


9. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.

  1. A098898E03
    Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.


10. REMOVE FUEL INLET PIPE SUB-ASSEMBLY
  1. Remove the engine oil level dipstick.

  1. G036615E01
    Remove the bolt and clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring engine oil level dipstick guide.

  1. A098969E03
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


11. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the fuel pressure sensor connector and pressure discharge valve connector.

  1. A152743
    Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the fuel pressure sensor and pressure discharge valve.

← COMPONENTS (from Aug 2013)REMOVAL (Aug 2012 – Jul 2013) →