2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ Intercooler)
(Click here)

4. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)

5. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)

6. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


7. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ Intercooler)

  1. A211857
    Disconnect the vacuum switching valve connector.

  1. A211858
    Disconnect the 3 vacuum transmitting hoses.

  1. A211859
    Remove the 2 bolts and manifold stay with vacuum switching valve.


8. REMOVE MANIFOLD STAY (w/o Intercooler)

  1. A099622E01
    Remove the 2 bolts and manifold stay.


9. REMOVE OIL FILTER SUB-ASSEMBLY

  1. A227248E01
    Using SST, remove the oil filter.
    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.


10. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. w/ Intercooler:

    1. A211871
      Remove the 2 nuts and No. 3 injection pipe clamp.

    2. A211872
      Remove the 2 bolts and 2 No. 2 injection pipe clamps.

    3. A272112E01
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side

  1. w/o Intercooler:

    1. A231803E02
      Remove the bolt and No. 2 injection pipe clamp.
      Text in Illustration 
      *1
      No. 2 Injection Pipe Clamp
      *2
      No. 3 Injection Pipe Clamp
      *a
      Injector Side
      *b
      Common Rail Side

    2. Remove the 2 nuts and No. 3 injection pipe clamp.

    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.


11. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ Intercooler)

  1. A273018E01
    Remove the 3 bolts and No. 2 intake air connector bracket.
    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler
    *1
    No. 2 Intake Air Connector Bracket
    *2
    Intake Air Connector


12. DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ Intercooler)

  1. A147216
    Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with the wire harness.


13. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ Intercooler)

  1. w/ Intercooler:

    1. A211846
      Disconnect the 2 connectors.

    2. A252294
      Disconnect the 6 vacuum hoses.

    3. Remove the bolt and No. 1 gas filter with gas filter bracket.

    4. A211848
      Remove the 2 bolts and electric vacuum regulating valve.

  1. w/o Intercooler:

    1. A212373
      Disconnect the connector.

    2. Disconnect the 2 vacuum hoses.

    3. Remove the 2 bolts and electric vacuum regulating valve together with the bracket.

      NOTICE:
      Do not remove the electric vacuum regulating valve from the bracket.


14. REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A147230
    Remove the 3 nuts, No. 2 intake air connector and gasket.


15. REMOVE INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A147219
    Remove the 3 bolts, intake air connector and 2 gaskets.


16. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 1 EGR PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A211879
    Remove the 2 nuts, electric EGR control valve with No. 1 EGR pipe and gasket.


17. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. w/ Intercooler:

    1. A152275
      Remove the bolt and disconnect the injection pipe clamp.

    2. A152276E07
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side

  1. w/o Intercooler:

    1. A098893E01
      Remove the 2 bolts and disconnect the 2 injection pipe clamps.

    2. A231804E02
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side


18. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.

  1. A271807E01
    w/ Intercooler:
    Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt

  1. A272915E01
    w/o Intercooler:
    Remove the union bolt, 2 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt


19. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A272134E01
    Remove the bolt and injection pipe clamp.
    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.


20. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A098969E11
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
    Text in Illustration 
    *a
    Common Rail Side
    *b
    Fuel Supply Pump Side


21. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the 2 connectors.

  1. A231856
    Remove the 2 bolts, common rail and No. 2 intake manifold insulator.

    NOTICE:
    Do not remove the pressure discharge valve or fuel pressure sensor.

← REMOVAL (Aug 2012 – Jul 2013)INSPECTION (from Jun 2011) →