2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

A111789
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the pipe together with the 2 air hoses.


3. CHECK FOR INJECTOR COMPENSATION CODE

HINT:
If the injector compensation code is not correctly registered, it may cause malfunctions.

  1. Read the injector compensation code (Click here).

  1. Check that compensation code of installed injector is same as code registered in ECM. If the code is not as specified, register the injector compensation code on the injector (Click here).


4. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A098967E05
    Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.


5. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A098893E01
    Remove the 2 bolts.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. A231804E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


6. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.

  1. A098898E03
    Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.


7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. G034844E02
    Disconnect the ventilation hose.

  1. Disconnect the 4 injector connectors.

  1. A060180E01
    Using a small screwdriver, remove the 4 nozzle holder seals by prying the portion between each nozzle holder seal and the cutout part of the cylinder head cover.

  1. G034877E01
    Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


8. REMOVE INJECTOR ASSEMBLY

  1. A061112E01
    Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. G034876E01
    Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.

← COMPONENTS (from Aug 2013)REMOVAL (Aug 2012 – Jul 2013) →