2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ Intercooler)
(Click here)

4. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o Intercooler)

A111789
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the pipe together with the 2 air hoses.


5. CHECK INJECTOR COMPENSATION CODE

HINT:
If the injector compensation code is not correctly registered, it may cause malfunctions.

  1. Read the injector compensation code (Click here).

  1. Check that the compensation code of the installed injector is the same as the code registered in the ECM. If the code is the same, register the injector compensation code on the injector (Click here).


6. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. w/ Intercooler:

    1. A211871
      Remove the 2 nuts and No. 3 injection pipe clamp.

    2. A211872
      Remove the 2 bolts and 2 No. 2 injection pipe clamps.

    3. A272112E01
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side

  1. w/o Intercooler:

    1. A231803E02
      Remove the bolt and No. 2 injection pipe clamp.
      Text in Illustration 
      *1
      No. 2 Injection Pipe Clamp
      *2
      No. 3 Injection Pipe Clamp
      *a
      Injector Side
      *b
      Common Rail Side

    2. Remove the 2 nuts and No. 3 injection pipe clamp.

    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.


7. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ Intercooler)

  1. A273018E01
    Remove the 3 bolts and No. 2 intake air connector bracket.
    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler
    *1
    No. 2 Intake Air Connector Bracket
    *2
    Intake Air Connector


8. DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ Intercooler)

  1. A147216
    Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with the wire harness.


9. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ Intercooler)

  1. w/ Intercooler:

    1. A211846
      Disconnect the 2 connectors.

    2. A252294
      Disconnect the 6 vacuum hoses.

    3. Remove the bolt and No. 1 gas filter with gas filter bracket.

    4. A211848
      Remove the 2 bolts and electric vacuum regulating valve.

  1. w/o Intercooler:

    1. A212373
      Disconnect the connector.

    2. Disconnect the 2 vacuum hoses.

    3. Remove the 2 bolts and electric vacuum regulating valve together with the bracket.

      NOTICE:
      Do not remove the electric vacuum regulating valve from the bracket.


10. REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A147230
    Remove the 3 nuts, No. 2 intake air connector and gasket.


11. REMOVE INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A147219
    Remove the 3 bolts, intake air connector and 2 gaskets.


12. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 1 EGR PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A211879
    Remove the 2 nuts, electric EGR control valve with No. 1 EGR pipe and gasket.


13. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. w/ Intercooler:

    1. A152275
      Remove the bolt and disconnect the injection pipe clamp.

    2. A152276E07
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side

  1. w/o Intercooler:

    1. A098893E01
      Remove the 2 bolts and disconnect the 2 injection pipe clamps.

    2. A231804E02
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side


14. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.

  1. A271807E01
    w/ Intercooler:
    Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt

  1. A272915E01
    w/o Intercooler:
    Remove the union bolt, 2 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt


15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. Remove the 3 bolts and disconnect the 4 injector connectors.

  1. A060180E01
    Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. Disconnect the ventilation hose.

  1. G034877E01
    Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


16. REMOVE INJECTOR ASSEMBLY

  1. A271617E01
    Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.
    Text in Illustration 
    *1
    Union Bolt

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A271618
    Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →