2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


3. REMOVE ENGINE ASSEMBLY
(Click here)

4. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A152281
    Remove the bolt and clamp.

  1. A153562
    Remove the bolt and oil level gauge guide.

  1. A152282E02
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


5. REMOVE EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE
(Click here)

6. REMOVE NO. 4 INJECTION PIPE

  1. A152275
    Remove the bolt and disconnect the injection pipe clamp.

  1. A152276E02
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. A152277
    Remove the 3 bolts and disconnect the 4 connectors.

  1. A060180E01
    Using a small screwdriver, remove the holder seal by prying the portion between the holder seal and the cutout part of the cylinder head.

  1. Disconnect the ventilation hose.

  1. G034877E01
    Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


8. REMOVE TIMING BELT
(Click here)

9. REMOVE CAMSHAFT TIMING PULLEY

  1. A060182E01
    Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.

    NOTICE:
    Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.

  1. Remove the camshaft timing pulley.


10. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

11. REMOVE CYLINDER BLOCK INSULATOR

  1. A149941
    Remove the cylinder block insulator from the cylinder head.


12. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nuts and No. 2 timing belt cover.


13. REMOVE WATER PUMP ASSEMBLY

  1. A225339
    Remove the 2 nuts, 5 bolts, engine water pump and gasket.


14. REMOVE TIMING GEAR COVER INSULATOR

  1. A148171
    Remove the bolt and timing gear cover insulator.


15. REMOVE VACUUM PUMP ASSEMBLY
  1. Disconnect the vacuum hose.

  1. A098930E01
    Remove the 2 nuts, vacuum pump and O-ring.


16. REMOVE VANE PUMP ASSEMBLY
  1. Remove the 2 nuts, vane pump and O-ring.

    HINT:
    It is not necessary to remove the hose from the vane pump. For the remaining removal procedures, you may put the removed assembly aside in an appropriate location.


17. REMOVE PUMP DRIVE SHAFT PULLEY

  1. A038747E01
    Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E03
    Using SST, hold the crankshaft pulley and remove the nut and O-ring.
    SST
    09213-58013  
    09330-00021  


18. REMOVE CRANKSHAFT PULLEY

  1. A072413E02
    Using SST, remove the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A072414E02
    Using SST, remove the pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.


19. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the sensor connector.

  1. Remove the 3 clips, bolt and sensor.

    A112048


20. REMOVE CAMSHAFT POSITION SENSOR

A112046
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.


21. REMOVE TIMING GEAR COVER
  1. Remove the wire harness clamp.

  1. A038748E01
    Remove the 14 bolts and 2 nuts.

  1. Using a slotted screwdriver, gently separate the cover from the timing gear case.

    HINT:
    There are tiny slots that allow you to insert the slotted screwdriver tip for separating the timing gear case and its cover. Refer to the illustration for the slot locations.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing gear case and its cover.

  1. Remove the cover and O-ring.


22. FIX NO. 1 IDLE GEAR

  1. A038749E03
    Fix the sub idle gears to the idle gear with the service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    Text in Illustration 
    *1
    Service Bolt

    NOTICE:
    If the screw hole position of the rear sub idle gear is incorrect, rotate the crankshaft counterclockwise to correct the hole position. Then install the service bolt.

    HINT:
    The service bolt is installed to eliminate torsional force caused by the idle gear springs, which are located between the idle gear and each sub idle gear. Torsional force will cause the sub idle gear's tooth and idle gear's tooth to be out of alignment.


23. REMOVE CRANKSHAFT TIMING GEAR

  1. A060163E01
    Remove the No. 1 crankshaft position sensor plate.

  1. A071161E01
    Using SST, remove the crankshaft timing gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05010)


24. REMOVE NO. 1 IDLE GEAR

  1. A038751E01
    Remove the 2 bolts, idle gear thrust plate.

  1. Remove the service bolt and idle gear.

  1. Remove the No. 1 idle gear shaft.


25. REMOVE INJECTION GEAR

  1. A071164E01
    Using SST, remove the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


26. REMOVE FUEL SUPPLY PUMP ASSEMBLY

  1. A153558
    Disconnect the 2 fuel hoses.

  1. A153559
    Disconnect the 2 connectors.

  1. A070710E01
    Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E02
    Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
    SST
    09213-58013  
    09330-00021  

  1. A153560
    Loosen the 2 nuts.

  1. A070714E01
    Using SST, disconnect the pump from the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.


27. REMOVE OIL DIPSTICK GUIDE

A148132
  1. Remove the bolt and injection pipe clamp.

  1. Remove the bolt and guide.

  1. Remove the O-ring from the guide.


28. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 22 bolts and 2 nuts.

  1. Z004119E04
    Insert the blade of a oil pan seal cutter between the cylinder block and oil pan. Cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use a oil pan seal cutter for the timing gear case and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.

  1. Remove the 2 bolts, nut, oil strainer and gasket.

  1. Clean off any sealer remaining the oil pan and cylinder block.


29. REMOVE TIMING GEAR CASE ASSEMBLY

A038755E01
  1. Remove the 8 bolts and union bolt. Then remove the timing gear case and its 2 O-rings.

    NOTICE:
    Do not drop the oil pump rotor.

  1. Remove the nut and No. 1 vacuum transmitting pipe.

  1. Remove the oil pump gasket.

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →