When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
Uniformly loosen the 2 bolts and remove the timing belt tensioner.
Remove the timing belt.
Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.
HINT:
When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.
4.
REMOVE NO. 1 TIMING BELT TENSIONER ASSEMBLY
5.
REMOVE NO. 2 IDLE PULLEY ASSEMBLY
6.
REMOVE GENERATOR ASSEMBLY
Remove the nut and generator wire.
Disconnect the generator connector.
Remove the 2 bolts and generator.
7.
REMOVE GENERATOR BRACKET
Remove the bolt and generator bracket.
8.
REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 4 bolts and V-ribbed belt tensioner.
9.
REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 4 bolts and No. 1 compressor mounting bracket.
10.
REMOVE MANIFOLD STAY
Remove the 2 bolts and stay.
11.
REMOVE FUEL INLET PIPE SUB-ASSEMBLY
Remove the engine oil level dipstick.
Remove the bolt and clamp.
Remove the bolt and engine oil level dipstick guide.
Remove the O-ring engine oil level dipstick guide.
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
Remove the bolt and No. 2 injection pipe clamp.
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
13.
REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY
Remove the 2 bolts and disconnect the 2 injection pipe clamps.
NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
14.
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.
Remove the 3 bolts and disconnect the 4 connectors.
Disconnect the ventilation hose.
Using a small screwdriver, remove the nozzle holder seal by prying the portion between the nozzle holder seal and the cutout part of the cylinder head cover.
Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.
Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.
15.
REMOVE CAMSHAFT TIMING PULLEY
Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
NOTICE:
Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.
Remove the camshaft timing pulley.
16.
REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
17.
REMOVE NO. 2 TIMING BELT COVER
Remove the 4 bolts, nuts and No. 2 timing belt cover.
18.
REMOVE WATER PUMP ASSEMBLY
Remove the 5 bolts, 2 nuts, water pump and gasket.
19.
REMOVE VACUUM PUMP ASSEMBLY
Remove the 2 nuts, vacuum pump and 2 O-rings.
20.
REMOVE VANE PUMP ASSEMBLY
Remove the 2 nuts, vane pump and O-ring.
21.
REMOVE PUMP DRIVE SHAFT PULLEY
Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.
Using SST, hold the crankshaft pulley and remove the nut and O-ring.
Apply oil or grease to the threads and tip of SST (center bolt) before using it.
23.
REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt and camshaft position sensor.
24.
REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and crankshaft position sensor.
25.
REMOVE TIMING GEAR COVER
Remove the bolt and No. 1 vacuum transmitting pipe.
Remove the 14 bolts and 2 nuts.
Using a slotted screwdriver, gently separate the cover from the timing gear case.
HINT:
There are tiny slots that allow you to insert the slotted screwdriver tip for separating the timing gear case and its cover. Refer to the illustration for the slot locations.
NOTICE:
Be careful not to damage the contact surfaces of the timing gear case and its cover.
Remove the cover and O-ring.
26.
FIX NO. 1 IDLE GEAR
Fix the sub idle gear to the idle gear with a service bolt.
Torque:
8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
NOTICE:
If the bolt hole of the sub idle gear is not aligned with the bolt hole of the idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.
HINT:
The service bolt is installed to eliminate torsional force caused by the idle gear springs, which are located between the idle gear and sub idle gear. Torsional force will cause the sub idle gear's tooth and idle gear's tooth to be out of alignment.