2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD)
  1. Remove the 4 bolts and No. 1 engine under cover.


3. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD)
  1. Remove the 2 bolts and No. 2 engine under cover.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.


6. LOOSEN FUEL TANK CAP ASSEMBLY

7. DRAIN FUEL

8. REMOVE EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE
  1. Remove the EGR cooler with electric EGR control valve and No. 2 EGR valve (Click here).


9. REMOVE NO. 4 INJECTION PIPE

  1. A152275
    Remove the bolt and disconnect the injection pipe clamp.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. A152276E05
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


10. REMOVE OIL DIPSTICK GUIDE

A148132
  1. Remove the bolt and injection pipe clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.


11. REMOVE MANIFOLD STAY

  1. A147226
    Disconnect the 2 connectors.

  1. A147227
    Disconnect the 4 vacuum hoses.

  1. A147228
    Remove the 2 bolts and manifold stay with VSV.


12. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A152338E02
    Disconnect the 3 fuel hoses.

  1. Remove the check valve, 3 bolts, leakage pipe and gasket.


13. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A152281
    Remove the bolt and clamp.

  1. A153562
    Remove the bolt and oil level gauge guide.

  1. A152282E03
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


14. REMOVE NO. 2 INTAKE MANIFOLD INSULATOR

15. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the 2 connectors.

  1. A224483
    Remove the 2 bolts, common rail and No. 2 intake manifold insulator.

    NOTICE:
    Do not remove the pressure discharge valve and pressure sensor.


16. REMOVE OIL FILTER SUB-ASSEMBLY

A147257E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil cooler cover. Put the disposal container beneath the drain hose to collect the oil from the oil cooler cover.


17. REMOVE STARTER ASSEMBLY

  1. A195903
    Disconnect the starter connector.

  1. Remove the nut and disconnect the starter wire.

  1. A195904
    Remove the nut, bolt, and disconnect the ground cable.

  1. Remove the starter.


18. REMOVE FUEL SUPPLY PUMP ASSEMBLY

  1. A153558
    Disconnect the 2 fuel hoses.

  1. A153559
    Disconnect the 2 connectors.

  1. A070710E01
    Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E02
    Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
    SST
    09213-58013  
    09330-00021  

  1. A153560
    Loosen the 2 nuts.

  1. A070714E01
    Using SST, disconnect the pump from the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.


19. REMOVE OIL COOLER COVER SUB-ASSEMBLY

A151174
  1. Disconnect the oil pressure switch connector and wire harness.

  1. Remove the 2 nuts and No. 2 vacuum transmitting pipe.

  1. Remove the 13 bolts and oil cooler cover.


20. REMOVE OIL COOLER ASSEMBLY

  1. A151173
    Loosen the 4 nuts first.

  1. Partially tap out the oil cooler by tapping each nut head with a plastic-faced hammer.

  1. Remove the 4 nuts, oil cooler and 2 gaskets.

← COMPONENTS (from Aug 2012)REMOVAL (Aug 2012 – Jul 2013) →