2014 Hilux · Service Manual BODY

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jun 2011


INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (except Double Cab, w/o Jam Protection)

  1. B289622E01
    for LHD:

    1. Measure the resistance of the power window switch.

      Standard resistance:
      for Driver switch:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (U) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 11 to 14 V
      4 (D) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V


      Standard resistance:
      for Passenger side switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      1 (E) - 10 (D)
      9 (B) - 8 (U)
      Below 1 Ω
      OFF
      OFF
      1 (E) - 8 (U)
      1 (E) - 10 (D)
      Below 1 Ω
      OFF
      DOWN
      1 (E) - 8 (U)
      9 (B) - 10 (D)
      Below 1 Ω
      ON
      UP
      1 (E) - 10 (D)
      10 kΩ or higher
      9 (B) - 8 (U)
      Below 1 Ω
      ON
      OFF
      8 (U) - 10 (D)
      Below 1 Ω
      ON
      DOWN
      1 (E) - 8 (U)
      10 kΩ or higher
      9 (B) - 10 (D)
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

    2. B289622E02
      Apply battery voltage to the master switch and check that the AUTO light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 9 (B)
      Battery negative (-) → Terminal 1 (E)
      AUTO light illuminates

      If the result is not as specified, replace the switch assembly.

    3. B289623E01
      Measure the resistance of the door control switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (E) - 2
      Lock
      Below 1 Ω
      1 (E) - 2
      1 (E) - 5
      OFF
      10 kΩ or higher
      1 (E) - 5
      Unlock
      Below 1 Ω

  1. B289620E01
    for RHD:

    1. Measure the resistance of the power window switch.

      Standard resistance:
      for Driver switch:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (U) - 10 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 11 to 14 V
      5 (D) - 10 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V


      Standard resistance:
      for Passenger side switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      10 (E) - 1 (D)
      9 (B) - 8 (U)
      Below 1 Ω
      OFF
      OFF
      10 (E) - 8 (U)
      10 (E) - 1 (D)
      Below 1 Ω
      OFF
      DOWN
      10 (E) - 8 (U)
      9 (B) - 1 (D)
      Below 1 Ω
      ON
      UP
      10 (E) - 1 (D)
      10 kΩ or higher
      9 (B) - 8 (U)
      Below 1 Ω
      ON
      OFF
      8 (U) - 1 (D)
      Below 1 Ω
      ON
      DOWN
      10 (E) - 8 (U)
      10 kΩ or higher
      9 (B) - 1 (D)
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

    2. B289620E02
      Apply battery voltage to the master switch and check that the AUTO light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 9 (B)
      Battery negative (-) → Terminal 10 (E)
      AUTO light illuminates

      If the result is not as specified, replace the switch assembly.

    3. B289624E01
      Measure the resistance of the door control switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      10 (E) - 3
      Lock
      Below 1 Ω
      10 (E) - 3
      10 (E) - 4
      OFF
      10 kΩ or higher
      10 (E) - 4
      Unlock
      Below 1 Ω


INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (except Double Cab, w/ Jam Protection)

B289617E03

  1. for LHD

    1. Measure the voltage of the power window regulator master switch connector.

      Standard voltage:
      for Driver switch:
      Tester Connection
      Condition
      Specified Condition
      4 (U) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed
      Below 1 V → 11 to 14 V → Below 1 V
      9 (D) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V


      Standard resistance:
      for Front passenger switch:
      Tester Connection
      Condition
      Specified Condition
      13 (U) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, front passenger side power window remote manual switch OFF → UP
      Below 1 V → 11 to 14 V
      15 (D) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, front passenger side power window remote manual switch OFF → DOWN
      Below 1 V → 11 to 14 V

      If the result is not as specified, replace the switch assembly.

    2. B289617E02
      Apply battery voltage to the master switch and check that the AUTO light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (B)
      Battery negative (-) → Terminal 1 (E)
      AUTO light illuminates

      If the result is not as specified, replace the switch assembly.

    3. B289625E03
      Measure the resistance of the door control switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (E) - 17
      Lock
      Below 1 Ω
      1 (E) - 17
      1 (E) - 18
      OFF
      10 kΩ or higher
      1 (E) - 18
      Unlock
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

  1. B282349E05
    for RHD

    1. Measure the voltage of the power window regulator master switch connector.

      Standard voltage:
      for Driver switch:
      Tester Connection
      Condition
      Specified Condition
      4 (U) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed
      Below 1 V → 11 to 14 V → Below 1 V
      9 (D) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V


      Standard resistance:
      for Front passenger switch:
      Tester Connection
      Condition
      Specified Condition
      13 (U) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, front passenger side power window remote manual switch OFF → UP
      Below 1 V → 11 to 14 V
      15 (D) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, front passenger side power window remote manual switch OFF → DOWN
      Below 1 V → 11 to 14 V

      If the result is not as specified, replace the switch assembly.

    2. B282349E06
      Apply battery voltage to the master switch and check that the AUTO light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (B)
      Battery negative (-) → Terminal 1 (E)
      AUTO light illuminates

      If the result is not as specified, replace the switch assembly.

    3. B289626E02
      Measure the resistance of the door control switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (E) - 17
      Lock
      Below 1 Ω
      1 (E) - 17
      1 (E) - 18
      OFF
      10 kΩ or higher
      1 (E) - 18
      Unlock
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.


INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Double cab, w/o Jam Protection)

  1. B289618E06
    for LHD:

    1. Measure the resistance of the power window switch.

      Standard resistance:
      for Driver switch:
      Tester Connection
      Switch Condition
      Specified Condition
      4 (U) - 3 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 11 to 14 V
      9 (D) - 3 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V


      Standard resistance:
      for Passenger side switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      3 (E) - 15 (D)
      6 (B) - 18 (U)
      Below 1 Ω
      OFF
      OFF
      3 (E) - 18 (U)
      3 (E) - 15 (D)
      Below 1 Ω
      OFF
      DOWN
      3 (E) - 18 (U)
      6 (B) - 15 (D)
      Below 1 Ω
      ON
      UP
      3 (E) - 15 (D)
      10 kΩ or higher
      6 (B) - 18 (U)
      Below 1 Ω
      ON
      OFF
      18 (U) - 15 (D)
      Below 1 Ω
      ON
      DOWN
      3 (E) - 18 (U)
      10 kΩ or higher
      6 (B) - 15 (D)
      Below 1 Ω


      Standard resistance:
      for Rear LH switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      3 (E) - 13 (D)
      6 (B) - 12 (U)
      Below 1 Ω
      OFF
      OFF
      3 (E) - 12 (U)
      3 (E) - 13 (D)
      Below 1 Ω
      OFF
      DOWN
      3 (E) - 12 (U)
      6 (B) - 13 (D)
      Below 1 Ω
      ON
      UP
      3 (E) - 13 (D)
      10 kΩ or higher
      6 (B) - 12 (U)
      Below 1 Ω
      ON
      OFF
      12 (U) - 13 (D)
      Below 1 Ω
      ON
      DOWN
      3 (E) - 12 (U)
      10 kΩ or higher
      6 (B) - 13 (D)
      Below 1 Ω


      Standard resistance:
      for Rear RH switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      3 (E) - 16 (D)
      6 (B) - 10 (U)
      Below 1 Ω
      OFF
      OFF
      3 (E) - 10 (U)
      3 (E) - 16 (D)
      Below 1 Ω
      OFF
      DOWN
      3 (E) - 10 (U)
      6 (B) - 16 (D)
      Below 1 Ω
      ON
      UP
      3 (E) - 16 (D)
      10 kΩ or higher
      6 (B) - 10 (U)
      Below 1 Ω
      ON
      OFF
      10 (U) - 16 (D)
      Below 1 Ω
      ON
      DOWN
      3 (E) - 10 (U)
      10 kΩ or higher
      6 (B) - 16 (D)
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

    2. B289618E02
      Apply battery voltage to the master switch and check that the AUTO light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (B)
      Battery negative (-) → Terminal 3 (E)
      AUTO light illuminates

      If the result is not as specified, replace the switch assembly.

    3. B289625E04
      Measure the resistance of the door control switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (E) - 5
      Lock
      Below 1 Ω
      3 (E) - 5
      3 (E) - 8
      OFF
      10 kΩ or higher
      3 (E) - 8
      Unlock
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

  1. B282348E10
    for RHD:

    1. Measure the resistance of the power window switch.

      Standard resistance:
      for Driver switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      Always
      (ON / OFF)
      UP
      3 (E) - 9 (D)
      4 (U) - 6 (B)
      Below 1 Ω
      Always
      (ON / OFF)
      OFF
      3 (E) - 4 (U)
      3 (E) - 9 (D)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN
      3 (E) - 4 (U)
      6 (B) - 9 (D)
      Below 1 Ω
      Always
      (ON / OFF)
      AUTO DOWN
      3 (E) - 4 (U)
      6 (B) - 9 (D)
      Below 1 Ω


      Standard resistance:
      for Passenger side switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      3 (E) - 13 (D)
      6 (B) - 10 (U)
      Below 1 Ω
      OFF
      OFF
      3 (E) - 10 (U)
      3 (E) - 13 (D)
      Below 1 Ω
      OFF
      DOWN
      3 (E) - 10 (U)
      6 (B) - 13 (D)
      Below 1 Ω
      ON
      UP
      3 (E) - 13 (D)
      10 kΩ or higher
      6 (B) - 10 (U)
      Below 1 Ω
      ON
      OFF
      10 (U) - 13 (D)
      Below 1 Ω
      ON
      DOWN
      3 (E) - 10 (U)
      10 kΩ or higher
      6 (B) - 13 (D)
      Below 1 Ω


      Standard resistance:
      for Rear RH switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      3 (E) - 15 (D)
      6 (B) - 16 (U)
      Below 1 Ω
      OFF
      OFF
      3 (E) - 16 (U)
      3 (E) - 15 (D)
      Below 1 Ω
      OFF
      DOWN
      3 (E) - 16 (U)
      6 (B) - 15 (D)
      Below 1 Ω
      ON
      UP
      3 (E) - 15 (D)
      10 kΩ or higher
      6 (B) - 16 (U)
      Below 1 Ω
      ON
      OFF
      16 (U) - 15 (D)
      Below 1 Ω
      ON
      DOWN
      3 (E) - 16 (U)
      10 kΩ or higher
      6 (B) - 15 (D)
      Below 1 Ω


      Standard resistance:
      for Rear LH switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      3 (E) - 12 (D)
      6 (B) - 18 (U)
      Below 1 Ω
      OFF
      OFF
      3 (E) - 18 (U)
      3 (E) - 12 (D)
      Below 1 Ω
      OFF
      DOWN
      3 (E) - 18 (U)
      6 (B) - 12 (D)
      Below 1 Ω
      ON
      UP
      3 (E) - 12 (D)
      10 kΩ or higher
      6 (B) - 18 (U)
      Below 1 Ω
      ON
      OFF
      18 (U) - 12 (D)
      Below 1 Ω
      ON
      DOWN
      3 (E) - 18 (U)
      10 kΩ or higher
      6 (B) - 12 (D)
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

    2. B282348E04
      Apply battery voltage to the master switch and check that the AUTO light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (B)
      Battery negative (-) → Terminal 3 (E)
      AUTO light illuminates

      If the result is not as specified, replace the switch assembly.

    3. B289626E03
      Measure the resistance of the door control switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (E) - 5
      Lock
      Below 1 Ω
      3 (E) - 5
      3 (E) - 8
      OFF
      10 kΩ or higher
      3 (E) - 8
      Unlock
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.


INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Double cab, w/ Jam Protection)

B289618E03

  1. for LHD

    1. Measure the voltage of the power window regulator master switch connector.

      Standard voltage:
      for Driver switch:
      Tester Connection
      Condition
      Specified Condition
      4 (U) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed
      Below 1 V → 11 to 14 V → Below 1 V
      9 (D) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V


      Standard resistance:
      for Front passenger switch:
      Tester Connection
      Condition
      Specified Condition
      13 (U) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, front passenger side power window remote manual switch OFF → UP
      Below 1 V → 11 to 14 V
      15 (D) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, front passenger side power window remote manual switch OFF → DOWN
      Below 1 V → 11 to 14 V


      Standard resistance:
      for Rear LH switch:
      Tester Connection
      Condition
      Specified Condition
      12 (U) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, rear power window LH remote manual switch OFF → UP
      Below 1 V → 11 to 14 V
      10 (D) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, rear power window LH remote manual switch OFF → DOWN
      Below 1 V → 11 to 14 V


      Standard resistance:
      for Rear RH switch:
      Tester Connection
      Condition
      Specified Condition
      18 (U) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, rear power window RH remote manual switch OFF → UP
      Below 1 V → 11 to 14 V
      16 (D) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, rear power window RH remote manual switch OFF → DOWN
      Below 1 V → 11 to 14 V

      If the result is not as specified, replace the switch assembly.

    2. B289618E05
      Apply battery voltage to the master switch and check that the AUTO light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (B)
      Battery negative (-) → Terminal 1 (E)
      AUTO light illuminates

      If the result is not as specified, replace the switch assembly.

    3. B289625E03
      Measure the resistance of the door control switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (E) - 5
      Lock
      Below 1 Ω
      1 (E) - 5
      1 (E) - 8
      OFF
      10 kΩ or higher
      1 (E) - 8
      Unlock
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

  1. B282348E08
    for RHD

    1. Measure the voltage of the power window regulator master switch connector.

      Standard voltage:
      for Driver switch:
      Tester Connection
      Condition
      Specified Condition
      4 (U) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully open → driver side power window switch UP (AUTO operation) → driver side power window fully closed
      Below 1 V → 11 to 14 V → Below 1 V
      9 (D) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 11 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V


      Standard resistance:
      for Front passenger switch:
      Tester Connection
      Condition
      Specified Condition
      13 (U) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, front passenger side power window remote manual switch OFF → UP
      Below 1 V → 11 to 14 V
      15 (D) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, front passenger side power window remote manual switch OFF → DOWN
      Below 1 V → 11 to 14 V


      Standard resistance:
      for Rear LH switch:
      Tester Connection
      Condition
      Specified Condition
      12 (U) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, rear power window LH remote manual switch OFF → UP
      Below 1 V → 11 to 14 V
      10 (D) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, rear power window LH remote manual switch OFF → DOWN
      Below 1 V → 11 to 14 V


      Standard resistance:
      for Rear RH switch:
      Tester Connection
      Condition
      Specified Condition
      18 (U) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, rear power window RH remote manual switch OFF → UP
      Below 1 V → 11 to 14 V
      16 (D) - 1 (E)
      1. Window lock switch OFF
      2. Ignition switch ON, rear power window RH remote manual switch OFF → DOWN
      Below 1 V → 11 to 14 V

      If the result is not as specified, replace the switch assembly.

    2. B282348E09
      Apply battery voltage to the master switch and check that the AUTO light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (B)
      Battery negative (-) → Terminal 1 (E)
      AUTO light illuminates

      If the result is not as specified, replace the switch assembly.

    3. B289626E02
      Measure the resistance of the door control switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (E) - 5
      Lock
      Below 1 Ω
      1 (E) - 5
      1 (E) - 8
      OFF
      10 kΩ or higher
      1 (E) - 8
      Unlock
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

← Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated) (from Jun 2011)ON-VEHICLE INSPECTION (from Jun 2011) →