2014 Hilux · Service Manual BODY

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jun 2011

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front LH)

B280842E04
  1. Apply battery voltage to connector terminals 1 and 2.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise

    1. If the result is not as specified, replace the power window regulator motor assembly.


INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front LH, w/Regulator)

B285951E01
  1. Apply battery voltage to connector terminals 1 and 2.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

  1. Check that the arm of window regulator rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Arm of window regulator rotates clockwise (Up)
    Battery positive (+) → 1
    Battery negative (-) → 2
    Arm of window regulator rotates counterclockwise (Down)

    1. If the result is not as specified, replace the power window regulator motor assembly.


INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front RH)

B280843E04
  1. Apply battery voltage to connector terminals 1 and 2.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise

    1. If the result is not as specified, replace the power window regulator motor assembly.


INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front RH, w/ Regulator)

B285952E01
  1. Apply battery voltage to connector terminals 1 and 2.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

  1. Check that the arm of window regulator rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Arm of window regulator rotates counterclockwise (Up)
    Battery positive (+) → 1
    Battery negative (-) → 2
    Arm of window regulator rotates clockwise (Down)

    1. If the result is not as specified, replace the power window regulator motor assembly.


INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH)

B280846E04
  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise

    1. If the result is not as specified, replace the power window regulator motor assembly.


INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH, w/ Regulator)

B285953E01
  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the arm of window regulator rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Arm of window regulator rotates clockwise (Up)
    Battery positive (+) → 1
    Battery negative (-) → 2
    Arm of window regulator rotates counterclockwise (Down)

    1. If the result is not as specified, replace the power window regulator motor assembly.


INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)

B280845E04
  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise

    1. If the result is not as specified, replace the power window regulator motor assembly.


INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH, w/ Regulator)

B285954E01
  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the arm of window regulator rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Arm of window regulator rotates counterclockwise (Up)
    Battery positive (+) → 1
    Battery negative (-) → 2
    Arm of window regulator rotates clockwise (Down)

    1. If the result is not as specified, replace the power window regulator motor assembly.

← ON-VEHICLE INSPECTION (from Jun 2011)COMPONENTS (Jun 2011 – Jul 2012) →