2014 Hilux · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012


CHECK INTAKE AIR SYSTEM
  1. Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and cylinder head.

    Condition
    Operation
    Clogged air cleaner
    Clean or replace
    Collapsed or deformed hoses
    Repair or replace
    Leakage from connections
    Check each connection and repair
    Cracks in components
    Check and replace


CHECK EXHAUST SYSTEM
  1. Check for leakage or clogging between the cylinder head and turbocharger inlet, and between the turbocharger outlet and exhaust pipe.

    Condition
    Operation
    Deformed components
    Repair or replace
    Foreign matter in passages
    Remove
    Leakage from components
    Repair or replace
    Cracks in components
    Check or replace


CHECK BOOST PRESSURE
  1. Warm up the engine.

    HINT:
    Be sure to perform the inspection when the engine coolant temperature is between 75 and 90°C (167 and 194°F).

  1. A110323E01
    Using a 3-way connector, connect SST (turbocharger pressure gauge) to the hose between the manifold absolute pressure sensor and the gas filter leading to the intake air connector.
    SST
    09992-00242  

  1. Fully apply the parking brake and chock the 4 wheels.

  1. for Manual Transmission:
    While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).

    Standard pressure (Gauge pressure):
    53 to 83 kPa (0.54 to 0.84 kgf/cm2, 7.6 to 12.0 psi)

  1. for Automatic Transmission:
    Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).

    Standard pressure (Gauge pressure):
    53 to 83 kPa (0.54 to 0.84 kgf/cm2, 7.6 to 12.0 psi)

    If the pressure is lower than the standard, the following problems may be present.
    1. The intake system or exhaust system has leakage or blockage.
    2. The turbocharger sub-assembly is malfunctioning.
    3. The EGR valve does not close.
    4. The diesel throttle body does not open.
    5. The vacuum hose connected to the diesel turbo pressure sensor (manifold absolute pressure sensor) is cracked or disconnected.
    6. The mass air flow meter is malfunctioning.
    7. A fuel injector is malfunctioning.
    If the pressure is higher than the standard, check the turbocharger and/or boost control components (pressure sensor, vacuum hose, etc.).

  1. Chart showing the suspected trouble areas when the pressure is lower than the standard.

    HINT:
    1. ○: If a problem listed in the leftmost column of the chart exists, or if the part in the leftmost column of the chart has a malfunction, the value of the Data List item in the uppermost row of the chart will meet the conditions shown in the row labeled "Value which represents a malfunction".
    2. The values in the chart are applicable when the engine coolant temperature is between 75 and 90°C (167 and 194°F).
    3. The values in the chart are for vehicles equipped with a manual transmission. For vehicles with an automatic transmission, use these values as a reference only as they may differ from the actual values.
    4. The values in the chart are valid in an area with an absolute atmospheric pressure higher than 95 kPa. (Standard atmospheric pressure is 101 kPa. Atmospheric pressure decreases by 1 kPa for every 100 m increase in altitude, and is also affected by the current weather conditions.)
    5. When the altitude increases, atmospheric pressure and MAP decrease.

    Item
    MAP
    (Absolute pressure inside intake manifold)
    MAF
    (Intake air flow rate)
    Accel Position
    Actual Throttle Position
    Actual EGR Valve Position
    EGR Close Lrn. Status
    (EGR valve fully closed position learning status)
    Fuel Pressure
    Injection Feedback Val #1 (to #4)
    Values taken from an actual normal vehicle
    *1
    -
    96 g/sec.
    99% or more
    None
    None
    OK
    -
    -3 to +3 mm3/st
    Values which represent a malfunction
    *1
    None
    MAF is less than 81 g/sec.
    Accel Position is not fully depressed position
    *2
    None
    None
    *3
    NG
    NG (Determined after performing learning)
    *3
    Fuel Pressure is lower than Target Common Rail Pressure by 10 MPa or more
    (Check while steady condition)
    Outside of above range
    Turbocharger
    ○
    ○
    -
    -
    -
    -
    -
    -
    EGR valve does not close or has problem with movement
    ○
    ○
    -
    -
    ○
    (Problem with EGR valve movement)
    *4
    ○
    (EGR valve does not close)
    *4
    -
    -
    Problem with diesel throttle movement
    ○
    (Intake airflow decreases)
    ○
    -
    ○
    -
    -
    -
    -
    Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists
    -
    ○
    ○
    -
    -
    -
    -
    -
    Intake air system leakage or blockage
    ○
    ○
    -
    -
    -
    -
    -
    -
    Exhaust gas leakage before turbocharger or blockage
    ○
    ○
    -
    -
    -
    -
    -
    -
    Manifold absolute pressure sensor
    ○
    ○
    -
    -
    -
    -
    -
    -
    Manifold absolute pressure sensor hose is disconnected
    ○
    ○
    -
    -
    -
    -
    -
    -
    Mass air flow meter sub-assembly
    -
    ○
    -
    -
    -
    -
    -
    -
    Fuel system (injector, supply pump or common rail)
    ○
    ○
    -
    -
    -
    -
    ○
    (Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck)
    ○
    *5

    HINT:
    1. *1: These values are measured when the transmission is in 2nd gear, the accelerator pedal is fully depressed, the vehicle is accelerating, and the engine speed is 3000 rpm.
    2. *2: The Accel Position is the accelerator opening angle (%) for engine control use. The value indicates around 100 % when the accelerator pedal fully depressed. If the value does not indicate around 100 % when the accelerator pedal fully depressed, the accelerator pedal position sensor circuit or the pedal itself is malfunctioning. When the MIL is illuminated, even with the accelerator pedal fully depressed and an Accel Position of below 70%, it means the fail-safe is restricting the accelerator.
    3. *3: The Data List items indicated on the tester differ according to vehicle model and engine type. If the Data List items Actual EGR Valve Pos. and EGR Lift Sensor Volt % are not available, troubleshoot the EGR valve malfunction by reading the MAF and/or MAP values in the Data List items. If the MAF and/or MAP values are lower than normal engine conditions, the EGR valve can be assumed to be malfunctioning (the valve cannot close fully). In this case, perform the Control the EGR System in the Active Test function while the engine is idling, and check that the MAF and/or MAP value fluctuates according to the Active Test operation. Inspect the EGR valve for any defects (deposits, valve stuck, poor movement, etc.) if necessary.
    4. *4: DTC P0400 may be stored at this time. If the actual EGR valve position follows the target EGR valve position slowly, a feeling of hesitation may occur.
    5. *5: If Injection Feedback Val # of a cylinder is not within -3 to +3 mm3/st, the corresponding cylinder may have a malfunction (injector or compression). However, in some cases the cylinder may be malfunctioning even if the value is within -3 to +3 mm3/st because these values are injection volume correction values calculated by the ECM at the engine idling and not correction values for the high engine load condition related to the boost pressure control and engine output performance.


CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

  1. A110327E01
    Inspect the power source voltage.

    1. Disconnect the pressure sensor connector.

    2. Turn the ignition switch ON.

    3. Measure the voltage between terminals T9-3 (VC (+)) and T9-1 (E2 (-)) of the wire harness side connector.

      Standard voltage:
      4.75 to 5.25 V

      If the result is not as specified, inspect the wire harness or ECM (Click here).

    4. Turn the ignition switch OFF.

    5. Connect the pressure sensor connector.

  1. G039061E02
    Check the power supply.

    1. Turn the ignition switch ON.

    2. Disconnect the vacuum hose from the pressure sensor.

    3. Connect a voltmeter to terminals E7-28 (PIM (+)) and E8-28 (E2 (-)) of the ECM, and measure the output voltage at ambient atmospheric pressure.

    4. A110329E01
      Apply a vacuum to the pressure sensor in 13.3 kPa (100 mmHg, 3.94 in.Hg) increments until the pressure reaches 40.0 kPa (300 mmHg, 11.81 in.Hg). Measure the decrease in voltage for each increment.

      Standard voltage:
      Applied Vacuum
      Voltage Decrease
      -13.3 kPa (100 mmHg, 3.94 in.Hg)
      0.1 to 0.4 V
      -26.6 kPa (199 mmHg, 7.85 in.Hg)
      0.2 to 0.6 V
      -40 kPa (300 mmHg, 11.81 in.Hg)
      0.4 to 0.8 V

      If the result is not as specified, replace the manifold absolute pressure sensor.

    5. A110331E01
      Using SST (turbocharger pressure gauge), apply pressure to the pressure sensor in 19.6 kPa (0.20 kgf*cm2, 2.84 psi) increments until the pressure reaches 98.0 kPa (1.00 kgf*cm2, 14.2 psi). Measure the increase in voltage for each increment.
      SST
      09992-00242  

      Standard voltage:
      Applied Pressure
      Voltage Increase
      19.6 kPa (0.20 kgf*cm2, 2.84 psi)
      0.1 to 0.4 V
      39.2 kPa (0.40 kgf*cm2, 5.69 psi)
      0.4 to 0.7 V
      58.8 kPa (0.60 kgf*cm2, 8.53 psi)
      0.7 to 1.0 V
      78.5 kPa (0.80 kgf*cm2, 11.4 psi)
      1.0 to 1.3 V
      98.0 kPa (1.00 kgf*cm2, 14.2 psi)
      1.3 to 1.6 V

      If the result is not as specified, replace the manifold absolute pressure sensor.

← SYSTEM DIAGRAM (from Aug 2012)ON-VEHICLE INSPECTION (from Aug 2012) →