2014 Hilux · Service Manual ENGINE

SYSTEM DIAGRAM

System information · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012


INTAKE AIR CONTROL SYSTEM ILLUSTRATION

  1. w/ Intercooler:
    The swirl control valve is mounted on the intake manifold. The Vacuum Switching Valve (VSV) for swirl control valve changes the vacuum to actuate the actuator.
    First, the ECM determines the opening angle of the swirl control valve. Then it uses the swirl control valve VSV to change the vacuum applied to the actuator's diaphragm to open and close the swirl control valve.
    A252794E03

    Text in Illustration (w/ Intercooler) 
    *1
    Accelerator Pedal Sensor
    *2
    ECM
    *3
    Air Cleaner
    *4
    Intercooler
    *5
    Diesel Throttle Body
    *6
    Manifold Absolute Pressure Sensor
    *7
    Vacuum Switching Valve (for Swirl Control Valve)
    *8
    Swirl Control Valve Actuator
    *9
    Swirl Control Valve
    *10
    Turbocharger
    *11
    Crankshaft Position Sensor
    -
    -

  2. w/o Intercooler:

    1. The manifold absolute pressure sensor detects the manifold pressure by using the built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the output voltage by the manifold absolute pressure sensor.

    2. The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa (0 mmHg, 0 in.Hg)), so that the ECM controls the air-fuel ratio at the proper level under any driving conditions, without influence of fluctuations in the atmospheric pressure due to factors such as high altitude, etc.

      A240570E03
      Text in Illustration (w/o Intercooler) 
      *1
      ECM
      *2
      Diesel Throttle Body
      *3
      Turbocharger
      *4
      Manifold Absolute Pressure Sensor


INTAKE AIR CONTROL SYSTEM WIRING DIAGRAM
A220713E10
A220714E18
A276716E02

TURBOCHARGER SYSTEM ILLUSTRATION (w/ Intercooler)

    1. The turbocharger system is comprised of the Variable Nozzle (VN) type turbocharger, turbo motor driver and ECM.
    2. The turbocharger has a nozzle vane which opens and closes to control the volume of the exhaust gas flowing into the turbine. This, in turn, controls the boost pressure. When the nozzle vane moves towards the closing direction, the pressure increases. When the vane moves towards the opening direction, the pressure decreases.
    3. The turbocharger actuator built on the compressor housing side activates the nozzle vane. The nozzle vane position sensor built on the actuator detects the opening angle of the nozzle vane. The turbo motor driver receives an opening angle request from the ECM and a nozzle vane position sensor signal. Based on these signals, the turbo motor driver operates the DC motor and controls the turbocharger's opening angle. The turbo motor driver sends the status as a turbo driver status signal to the ECM.
    4. The ECM sends a target nozzle vane position signal to the turbo motor driver to obtain the nozzle vane position for optimal pressure in accordance with the driving conditions.
    A252795E02
    Text in Illustration (w/ Intercooler) 
    *1
    ECM
    *2
    Air Cleaner
    *3
    Intercooler
    *4
    Diesel Throttle Body
    *5
    Manifold Absolute Pressure Sensor
    *6
    Turbocharger Actuator
    - Turbocharger Variable Nozzle Motor
    - Turbocharger Variable Nozzle Sensor
    *7
    Turbocharger
    *8
    Turbo Motor Driver
    *9
    Crankshaft Position Sensor
    -
    -


TURBOCHARGER SYSTEM WIRING DIAGRAM (w/ Intercooler)
A220715E12
← SYSTEM DIAGRAM (Jun 2011 – Jul 2012)ON-VEHICLE INSPECTION (Jun 2011 – Jul 2012) →