2014 Hilux · Service Manual ENGINE

ADJUSTMENT

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. DRAIN ENGINE COOLANT
  1. Remove the radiator cap.

  1. Loosen the cylinder block drain cock plug and radiator drain plug, and then the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A270641E01


3. REMOVE V-BANK COVER

  1. A112983
    Remove the 2 nuts and the V-bank cover.


4. REMOVE NO. 2 VENTILATION HOSE

A075594

5. REMOVE AIR CLEANER

  1. A075595
    Disconnect the vacuum hose.

  1. Disconnect the MAF meter connector.

  1. Remove the 2 wire harness clamps.

  1. A075596
    Loosen the 2 hose clamps.

  1. Remove the 2 bolts and air cleaner.


6. REMOVE INTAKE AIR SURGE TANK

A076500E02
  1. Disconnect the 2 water by-pass hoses.

  1. A075644E01
    Disconnect the purge line hose.

  1. A075645E01
    Disconnect the ventilation hose.

  1. A075646E01
    Disconnect the 2 VSV connectors.

  1. Disconnect the throttle body with motor connector.

  1. Separate the 3 wire harness clamps and hose clamp.

  1. A076501E01
    Remove the 2 bolts and throttle body bracket.

  1. A076502E01
    Remove the bolt and oil baffle plate.

  1. Remove the 4 bolts and 2 surge tank stays.

  1. A075648E01
    Remove the 2 nuts.

  1. Using an 8 mm hexagon socket wrench, remove the 4 bolts, intake air surge tank and gasket.


7. REMOVE IGNITION COIL

8. REMOVE CYLINDER HEAD COVER RH

  1. A072943E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, head cover and gasket.


9. REMOVE CYLINDER HEAD COVER LH

  1. A072944E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.

  1. Remove the ventilation valve from the cylinder head cover.


10. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A076530E01
    Turn the crankshaft pulley, and align its groove with the timing mark 0 of the timing chain cover.

  1. G038065E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.


11. INSPECT VALVE CLEARANCE

  1. G036072E01
    Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Valve clearance (Cold):
      Intake 0.15 to 0.25 mm (0.006 to 0.010 in.)
      Exhaust 0.29 to 0.39 mm (0.011 to 0.015 in.)

      HINT:
      Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.

  1. G036073E01
    Turn the crankshaft 2/3 of a revolution (240°), and check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Valve clearance (Cold):
      Intake 0.15 to 0.25 mm (0.006 to 0.010 in.)
      Exhaust 0.29 to 0.39 mm (0.011 to 0.015 in.)

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.

  1. A076345E01
    Turn the crankshaft 2/3 of a revolution (240°), and check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Valve clearance (Cold):
      Intake 0.15 to 0.25 mm (0.006 to 0.010 in.)
      Exhaust 0.29 to 0.39 mm (0.011 to 0.015 in.)

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.


12. ADJUST VALVE CLEARANCE

  1. A076530E01
    Set No. 1 cylinder to TDC/compression.

    1. Turn the crankshaft pulley, and align the notch with the timing mark 0 of the timing chain cover.

    2. G038065E01
      Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
      If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.

    3. G038066E01
      Place paint marks on the No. 1 chain links that correspond with the timing marks of the camshaft timing gears.

  1. Remove the No. 1 chain tensioner.

    NOTICE:
    1. Never rotate the crankshaft with the chain tensioner removed.
    2. When rotating the camshaft with the timing chain removed, turn the crankshaft counterclockwise 40° from the TDC first.


    1. A076506E01
      Remove the 4 bolts, timing chain cover plate and gasket.

    2. A072958E01
      While rotating the stopper plate of the tensioner upward, push in the plunger of the chain tensioner as shown in the illustration.

    3. While rotating the stopper plate of the tensioner downward, insert a bar of 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

    4. Remove the 2 bolts and chain tensioner.

  1. Remove the No. 2 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which are received the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. G038067E02
      While raising up the No. 2 chain tensioner, insert a diameter of 1.0 mm (0.039 in.) into the hole to fix it.

    2. G038068E02
      Hold the hexagonal portion of the No. 2 camshaft with a wrench, and remove the camshaft timing gear set bolt.

      NOTICE:
      Be careful not to damage the cylinder head and valve lifter with the wrench.

    3. Separate the camshaft timing gear from the No. 2 camshaft.

    4. G038069E01
      Rotate the camshaft counterclockwise using the wrench so that the cam lobes of the No. 1 cylinder faces upward as shown in the illustration.

    5. A076510E01
      Uniformly loosen and remove the 8 bearing cap bolts in several passes in the sequence shown in the illustration.

    6. Remove the 4 bearing caps and No. 2 camshaft.

  1. G038070E01
    Remove the No. 2 chain tensioner.

    1. Remove the No. 2 chain tensioner bolt, and then remove the No. 2 chain tensioner and camshaft timing gear.

  1. Remove the No. 1 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which are received the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. G038072E01
      Hold the hexagonal portion of the No. 1 camshaft with a wrench, and loosen the camshaft timing gear set bolt.

      NOTICE:
      1. Be careful not to damage the cylinder head and valve lifter with the wrench.
      2. Do not disassemble the camshaft timing gear assembly.

    2. G038071E01
      Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.

    3. G038073E01
      Rotate the No. 1 camshaft counterclockwise using the wrench so that the cam lobes of No. 1 cylinder faces upward as shown in the illustration.

    4. A076515E01
      Uniformly loosen and remove the 8 bearing cap bolts in several passes in the sequence shown in the illustration.

    5. Remove the 4 bearing caps.

    6. G038074E01
      Remove the camshaft timing gear set bolt with the No. 1 camshaft lifted up, and then remove the No. 1 camshaft and camshaft timing gear w/ No. 2 chain.

    7. A076517E01
      Tie the No. 1 chain with a string as shown in the illustration.

      NOTICE:
      Be careful not to drop anything inside the timing chain cover.

  1. Remove the No. 4 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which are received the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. G038075E01
      While pushing down the No. 3 chain tensioner, insert a pin of diameter of 1.0 mm (0.039 in.) into the hole to fix it.

    2. G038076E01
      Hold the hexagonal portion of the No. 4 camshaft with a wrench, and remove the camshaft timing gear set bolt.

      NOTICE:
      Be careful not to damage the cylinder head and valve lifter with the wrench.

    3. Separate the camshaft timing gear from the No. 4 camshaft.

    4. A076482E01
      Uniformly loosen and remove the 8 bearing cap bolts in several passes in the sequence shown in the illustration.

    5. Remove the 4 bearing caps and No. 4 camshaft.

  1. G038077E01
    Remove the No. 3 chain tensioner assembly.

    1. Remove the No. 3 chain tensioner bolt, and then remove the No. 3 chain tensioner and camshaft timing gear.

  1. Remove the No. 3 camshaft sub-assembly

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which received the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. A076809E01
      Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.

    2. Remove the 4 bearing caps.

    3. G038078E01
      Hold the No. 1 chain, and remove the No. 3 camshaft, camshaft timing gear and No. 2 chain.

    4. A076489E01
      Tie the No. 1 chain with a string as shown in the illustration.

      NOTICE:
      Be careful not to drop anything inside the timing chain cover.

  1. Remove the valve lifters.

  1. Determine the replacement valve lifter size according to these Formula or Charts:

    1. Using a micrometer, measure the thickness of the removed lifter.

    2. Calculate the thickness of a new lifter so that the valve clearance comes within the specified value.

      T:
      Thickness of removed lifter

      A:
      Measured valve clearance

      N:
      Thickness of new lifter

      Intake:
      N = T + (A to 0.20 mm (0.008 in.))

      Exhaust:
      N = T + (A to 0.30 mm (0.012 in.))

    3. Select a new intake side lifter with a thickness as close as possible to the calculated value.

      HINT:
      Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).

    4. Valve lifter selection chart (intake).

      A113394E03

    5. Valve lifter selection chart (intake) (continued).

      A113395E03

      New lifter thickness mm (in.):
      No.
      Thickness
      No.
      Thickness
      No.
      Thickness
      06
      5.060 (0.1992)
      30
      5.300 (0.2087)
      54
      5.540 (0.2181)
      08
      5.080 (0.2000)
      32
      5.320 (0.2094)
      56
      5.560 (0.2189)
      10
      5.100 (0.2008)
      34
      5.340 (0.2102)
      58
      5.580 (0.2197)
      12
      5.120 (0.2016)
      36
      5.360 (0.2110)
      60
      5.600 (0.2205)
      14
      5.140 (0.2024)
      38
      5.380 (0.2118)
      62
      5.620 (0.2213)
      16
      5.160 (0.2031)
      40
      5.400 (0.2126)
      64
      5.640 (0.2220)
      18
      5.180 (0.2039)
      42
      5.420 (0.2134)
      66
      5.660 (0.2189)
      20
      5.200 (0.2047)
      44
      5.440 (0.2142)
      68
      5.680 (0.2236)
      22
      5.220 (0.2055)
      46
      5.460 (0.2150)
      70
      5.700 (0.2244)
      24
      5.240 (0.2063)
      48
      5.480 (0.2157)
      72
      5.720 (0.2252)
      26
      5.260 (0.2071)
      50
      5.500 (0.2165)
      74
      5.740 (0.2260)
      28
      5.280 (0.2079)
      52
      5.520 (0.2173)


      Intake valve clearance (Cold):
      0.15 to 0.25 mm (0.006 to 0.010 in.)

      Example:
      The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0158 in.)
      Replace the 5.250 mm (0.2067 in.) lifter with a new No. 46 lifter.

    6. Valve lifter selection chart (exhaust).

      A113396E01

    7. Valve lifter selection chart (exhaust) (continued).

      A113397E01

      New lifter thickness mm (in.):
      No.
      Thickness
      No.
      Thickness
      No.
      Thickness
      06
      5.060 (0.1992)
      30
      5.300 (0.2087)
      54
      5.540 (0.2181)
      08
      5.080 (0.2000)
      32
      5.320 (0.2094)
      56
      5.560 (0.2189)
      10
      5.100 (0.2008)
      34
      5.340 (0.2102)
      58
      5.580 (0.2197)
      12
      5.120 (0.2016)
      36
      5.360 (0.2110)
      60
      5.600 (0.2205)
      14
      5.140 (0.2024)
      38
      5.380 (0.2118)
      62
      5.620 (0.2213)
      16
      5.160 (0.2031)
      40
      5.400 (0.2126)
      64
      5.640 (0.2220)
      18
      5.180 (0.2039)
      42
      5.420 (0.2134)
      66
      5.660 (0.2189)
      20
      5.200 (0.2047)
      44
      5.440 (0.2142)
      68
      5.680 (0.2236)
      22
      5.220 (0.2055)
      46
      5.460 (0.2150)
      70
      5.700 (0.2244)
      24
      5.240 (0.2063)
      48
      5.480 (0.2157)
      72
      5.720 (0.2252)
      26
      5.260 (0.2071)
      50
      5.500 (0.2165)
      74
      5.740 (0.2260)
      28
      5.280 (0.2079)
      52
      5.520 (0.2173)


      Exhaust valve clearance (Cold):
      0.29 to 0.39 mm (0.011 to 0.015 in.)

      Example:
      The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.480 mm (0.0189 in.)
      Replace the 5.340 mm (0.2102 in.) lifter with a new No. 48 lifter.

      HINT:
      Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).

  1. Install the No. 3 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. A076490E02
      Align the mark link (yellow) with the timing mark (2 dot marks) of the camshaft timing gear as shown in the illustration.

    2. Apply new engine oil to the thrust portion and journal of the camshafts.

    3. G038079E01
      Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.

    4. G038080E01
      Set the No. 3 camshaft onto the LH cylinder head with the cam lobes of the No. 2 cylinder faces downward as shown in the illustration.

    5. A076494E01
      Install the 4 bearing caps in their proper locations.

    6. Apply a light coat of engine oil on the threads of the bearing cap bolts.

    7. A076487E03
      Install the 8 bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for 10 mm (0.39 in.) head
      24 N*m{ 245 kgf*cm , 18 in.*lbf } for 12 mm (0.47 in.) head (A)

    8. G038081E01
      Set the paint mark of the No. 1 chain between the timing marks of the camshaft timing gear.

  1. A076289E01
    Install the No. 3 chain tensioner.

    1. While pushing in the tensioner, insert a diameter 1.0 mm (0.039 in.) pin into the hole to hold to fix it in place.

    2. G038082E01
      Temporarily install the camshaft timing gear and No. 3 chain tensioner and align the mark links (yellow) with the timing marks (1 dot mark and 2 dot marks) of the camshaft timing gears.

    3. Tighten the No. 3 chain tensioner bolt.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Install the No. 4 camshaft sub-assembly.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. G038083E01
      Align the knock pin hole in the camshaft timing gear with the knock pin of the No. 4 camshaft, and insert the No. 4 camshaft into the camshaft timing gear.

    2. Temporarily install the camshaft timing gear set bolt.

    3. A076498E01
      Install the 4 bearing caps in their proper locations.

    4. Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.

    5. A076482E03
      Install the 8 bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for 10 mm (0.39 in.) head
      24 N*m{ 245 kgf*cm , 18 ft.*lbf } for 12 mm (0.47 in.) head (A)

    6. G038076E02
      Hold the hexagonal portion of the No. 4 camshaft with a wrench, and tighten the camshaft timing gear set bolt.

      Torque:
      100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }

    7. Remove the pin from the No. 3 chain tensioner.

  1. Install the camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. A076518E02
      Align the mark link (yellow) with the timing mark (1 dot mark) of the camshaft timing gear as shown in the illustration.

    2. Apply new engine oil to the thrust portion and journal of the camshafts.

    3. A076519E01
      Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.

    4. G038084E01
      Align the knock pin hole in the camshaft timing gear with the knock pin of the No. 1 camshaft, and insert the No. 1 camshaft into the camshaft timing gear.

    5. Temporarily install the camshaft timing gear set bolt.

    6. G038085E01
      Set the No. 1 camshaft onto the RH cylinder head with the cam lobes of the No. 1 cylinder faces downward as shown in the illustration.

    7. A076522E01
      Install the 4 bearing caps in their proper locations.

    8. Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.

    9. A076515E04
      Install the 8 bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for 10 mm (0.39 in.) head
      24 N*m{ 245 kgf*cm , 18 ft.*lbf } for 12 mm (0.39 in.) head (A)

    10. G038086E01
      Rotate the No. 1 camshaft clockwise using hexagonal portion of the No. 1 camshaft so that the timing mark of the camshaft timing gear is aligned with the timing marks of the camshaft bearing cap.

    11. G038087E01
      Align the paint mark of the No. 1 chain with the timing mark of the camshaft timing gear.

    12. G038072E01
      Hold the hexagonal portion of the No. 1 camshaft with a wrench, and tighten the camshaft timing gear set bolt.

      Torque:
      100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }

  1. A076286E01
    Install the No. 2 chain tensioner.

    1. While pushing in the tensioner, insert a diameter of 1.0 mm (0.039 in.) pin into the hole to fix it in place.

    2. G038088E01
      Temporarily install the camshaft timing gear and No. 2 chain tensioner and align the mark links (yellow) with the timing marks (1 dot mark) of the camshaft timing gears.

    3. Tighten the chain tensioner No. 2 bolt.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Install the No. 2 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. G038089E01
      Set the No. 2 camshaft onto the RH cylinder head with the cam lobes of No. 1 cylinder faces upward as shown in the illustration.

    2. A076527E01
      Install the 4 bearing caps in their proper locations.

    3. Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.

    4. A076510E04
      Install the 8 bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for 10 mm (0.39 in.) head
      24 N*m{ 245 kgf*cm , 18 ft.*lbf } for 12 mm (0.47 in.) head (A)

    5. G038090E01
      Rotate the No. 2 camshaft clockwise using the wrench so that the knock pin of the No. 2 camshaft is aligned with the knock pin hole of the camshaft timing gear.

    6. G038068E01
      Hold the hexagonal portion of the No. 2 camshaft with a wrench, and install the camshaft timing gear set bolt.

      Torque:
      100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }

    7. Remove the pin from the No. 2 chain tensioner.

  1. A076294E01
    Install the No. 1 chain tensioner.

    1. While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.

    2. While turning the stopper plate of the tensioner counterclockwise, insert a bar of diameter of 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

    3. Install the chain tensioner with the 2 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    4. Remove the bar from the chain tensioner.

    5. Install a new gasket and the timing chain cover plate with the 4 bolts.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    6. A076530E01
      Slowly turn the crankshaft pulley 2 complete revolutions, and align the notch with timing mark 0 of the timing chain cover.

    7. G038065E01
      Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.


13. INSTALL CYLINDER HEAD COVER LH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.

  1. Apply adhesive on the threads of the ventilation valve.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the ventilation valve to the cylinder head cover.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. Install the gasket to the cylinder head cover.

  1. A076311E01
    Apply a continuous bead of the seal packing to the cylinder head and timing chain cover as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    2 to 3 mm (0.08 to 0.12 in.)

    NOTICE:
    Install the cylinder head cover within 3 minutes after applying seal packing. After installing it, cylinder head cover bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

  1. Install the seal washers to the bolts.

  1. A076503E06
    Install the cylinder head cover with the 10 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several passes.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for bolt A
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt B
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for nut


14. INSTALL CYLINDER HEAD COVER RH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.

  1. Install the gasket to the cylinder head cover.

  1. A076310E01
    Apply a continuous bead of the seal packing to the cylinder head and timing chain cover as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    2 to 3 mm (0.08 to 0.12 in.)

    NOTICE:
    Install the cylinder head cover within 3 minutes after applying seal packing. After installing it, cylinder head cover bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

  1. Install the seal washers to the bolts.

  1. A072943E05
    Install the cylinder head cover with the 10 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several passes.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for bolt A
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt B
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for nut


15. INSTALL IGNITION COIL

16. INSTALL INTAKE AIR SURGE TANK

  1. A075648E01
    Install a new gasket to the intake air surge tank.

  1. Using an 8 mm hexagon socket wrench, install the intake air surge tank with the 4 bolts. Install the 2 nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. A076502E01
    Install the 2 surge tank stays with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the oil baffle plate with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A075646E01
    Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the 3 wire harness clamps and hose clamp.

  1. Connect the throttle body with motor connector.

  1. Connect the 2 VSV connectors.

  1. A075645E01
    Connect the ventilation hose.

  1. A075644E01
    Connect the purge line hose.

  1. A076500E02
    Connect the 2 water by-pass hoses.


17. INSTALL AIR CLEANER

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


18. CONNECT NO. 2 VENTILATION HOSE

19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

20. ADD ENGINE COOLANT
  1. Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

    Standard capacity:
    Item
    Specified Condition
    A/T
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    M/T
    8.5 liters (9.0 US qts, 7.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic and technology consists of a combination of low phosphates and organic acids).
    2. Please contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.

  1. Install the radiator cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2,000 to 2,500 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A112081E01
    Check the coolant level in the radiator reservoir.
    If the coolant level is low, add SLLC to the reservoir F line.


21. CHECK FOR ENGINE COOLANT LEAKS
  1. Check for the engine coolant leaks (Click here).


22. INSTALL V-BANK COVER

Torque:
7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


23. INSPECT IGNITION TIMING

  1. A098433E01
    When using intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

      HINT:
      Please refer to the intelligent tester operator's manual for further details.

      Ignition timing:
      7 to 24°BTDC @ idle
      (Transmission in neutral position)

    2. Disconnect the intelligent tester from the DLC3.

  1. A076315E01
    When not using intelligent tester.
    Check the ignition timing.

    1. Remove the air cleaner cap.

    2. Connect the tester probe of a timing light to the green-red read wire of the ignition coil connector for the No.1 cylinder.

    3. G039198E01
      Using SST, connect terminals TC and CG of the DLC3.
      SST
      09843-18040  

    4. A076316E01
      Using the timing light, check the ignition timing.

      Ignition timing:
      10 +- 2° BTDC @ idle
      (Transmission in neutral position)

    5. Remove the SST from the DLC3.

    6. Check the ignition timing.

      Ignition timing:
      7 to 24° BTDC @ idle
      (Transmission in neutral position)

    7. Disconnect the timing light from the engine.

    8. Install the air cleaner cap.


24. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting the cable from negative (-) battery terminal.

← ADJUSTMENT (Jun 2011 – Jul 2012)ADJUSTMENT (from Aug 2013) →