2014 Hilux · Service Manual BODY

INSPECTION

Inspection · Vehicles built from Jun 2011


INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

B203252E07
  1. Inspect the outer mirror switch assembly.

    1. Select "L" on the select switch.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      4 (MLV) - 8 B
      6 (M+) - 7 E
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      4 (MLV) - 7 E
      6 (M+) - 8 B
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (MLH) - 8 B
      6 (M+) - 7 E
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (MLH) - 7 E
      6 (M+) - 8 B
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch assembly.

    3. Select "R" on the select switch.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (MRV) - 8 B
      6 (M+) - 7 E
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      3 (MRV) - 7 E
      6 (M+) - 8 B
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (MRH) - 8 B
      6 (M+) - 7 E
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (MRH) - 7 E
      6 (M+) - 8 B
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)
      *b
      Select switch
      *c
      Retract Switch


INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

B207176E05
  1. Inspect the outer mirror switch.

    1. Select "L" on the select switch.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      4 (MLV) - 8 B
      6 (M+) - 7 E
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      4 (MLV) - 7 E
      6 (M+) - 8 B
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (MLH) - 8 B
      6 (M+) - 7 E
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (MLH) - 7 E
      6 (M+) - 8 B
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch assembly.

    3. Select "R" on the select switch.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (MRV) - 8 B
      6 (M+) - 7 E
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      3 (MRV) - 7 E
      6 (M+) - 8 B
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (MRH) - 8 B
      6 (M+) - 7 E
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (MRH) - 7 E
      6 (M+) - 8 B
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)
      *b
      Select switch
      *c
      Retract Switch

  1. Inspect the retract switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 E - 10 (MF)
      8 B - 9 (MR)
      Pushed in
      Below 1 Ω
      7 E - 9 (MR)
      8 B - 10 (MF)
      Not pushed in
      Below 1 Ω

      If the result is not as specified, replace the outer mirror switch assembly.


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

  1. B263446E02
    Disconnect the mirror connector.

  1. Apply battery voltage and check operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) →Terminal 9 (MV)
    Battery negative (-) → Terminal 8 (M+)
    Turns upward
    Battery positive (+) → Terminal 8 (M+)
    Battery negative (-) → Terminal 9 (MV)
    Turns downward
    Battery positive (+) → Terminal 4 (MH)
    Battery negative (-) → Terminal 8 (M+)
    Turns left
    Battery positive (+) → Terminal 8 (M+)
    Battery negative (-) → Terminal 4 (MH)
    Turns right

    If the result is not as specified, replace the outer rear view mirror assembly LH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)

  1. B263448E02
    w/ Retract Mirror:

    1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Forward position A
      Moves from A to retracted position E
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Forward position A
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Position between forward position A and driving position C
      Moves from B to retracted position E
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Position between forward position A and driving position C
      Moves from B to retracted position A
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Driving position C
      Moves from C to retracted position E
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Driving position C
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Position between driving position C and retracted position E
      Moves from D to retracted position E
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Position between driving position C and retracted position E
      Moves from D to retracted position C
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Retracted position E
      Does not move
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Retracted position E
      Moves from E to driving position C

      NOTICE:
      1. Disconnect and reconnect the battery between each mirror position check.
      2. Do not apply battery voltage when moving the mirror by hand into each mirror position.

      If the result is not as specified, replace the outer rear view mirror assembly LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)

  1. B285956E01
    w/ Mirror Heater:
    Check the mirror heater.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (HL+) - 5 (HL-)
      25°C (75°F)
      4 to 12 Ω

      If the result is not as specified, replace the outer rear view mirror assembly LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)

    2. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (HL+)
      Battery negative (-) → Terminal 5 (HL-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.

  1. w/ side turn signal light:

    1. B276055E01
      Check the side turn signal light.
      Apply battery voltage to the terminals of the connector, and check the illumination condition.

      OK:
      Tester Connection
      Specified Condition
      Battery positive (+) → Terminal 10 (TRNL)
      Battery negative (-) → Terminal 6 (GND)
      Side turn light illuminates

      If the result is not as specified, replace the side turn signal light assembly LH (Click here).
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

  1. B263445E02
    Disconnect the mirror connector.

  1. Apply battery voltage and check operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) →Terminal 9 (MV)
    Battery negative (-) → Terminal 8 (M+)
    Turns upward
    Battery positive (+) → Terminal 8 (M+)
    Battery negative (-) → Terminal 9 (MV)
    Turns downward
    Battery positive (+) → Terminal 4 (MH)
    Battery negative (-) → Terminal 8 (M+)
    Turns left
    Battery positive (+) → Terminal 8 (M+)
    Battery negative (-) → Terminal 4 (MH)
    Turns right

    If the result is not as specified, replace the outer rear view mirror assembly RH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)

  1. B263447E02
    w/ Retract Mirror:

    1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Forward position A
      Moves from A to retracted position E
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Forward position A
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Position between forward position A and driving position C
      Moves from B to retracted position E
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Position between forward position A and driving position C
      Moves from B to retracted position A
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Driving position C
      Moves from C to retracted position E
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Driving position C
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Position between driving position C and retracted position E
      Moves from D to retracted position E
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Position between driving position C and retracted position E
      Moves from D to retracted position C
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 2 (MF)
      Retracted position E
      Does not move
      Battery negative (-) → Terminal 7 (MR)
      Battery positive (+) → Terminal 2 (MF)
      Retracted position E
      Moves from E to driving position C

      NOTICE:
      1. Disconnect and reconnect the battery between each mirror position check.
      2. Do not apply battery voltage when moving the mirror by hand into each mirror position.

      If the result is not as specified, replace the outer rear view mirror assembly RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

  1. B285955E01
    w/ Mirror Heater:
    Check the mirror heater.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (HR+) - 5 (HR-)
      25°C (75°F)
      4 to 12 Ω

      If the result is not as specified, replace the outer rear view mirror assembly RH.

    2. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (HR+)
      Battery negative (-) → Terminal 5 (HR-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

  1. w/ side turn signal light:

    1. B276055E02
      Check the side turn signal light.
      Apply battery voltage to the terminals of the connector, and check the illumination condition.

      OK:
      Tester Connection
      Specified Condition
      Battery positive (+) → Terminal 10 (TRNR)
      Battery negative (-) → Terminal 6 (GND)
      Side turn light illuminates

      If the result is not as specified, check the side turn signal light assembly RH (Click here).
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)

← PROBLEM SYMPTOMS TABLE (from Jun 2011)COMPONENTS (Jun 2011 – Jul 2012) →