2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL LH (w/ Power Window)

  1. B277019E01
    Using a moulding remover, detach the 2 clips.

  1. Disconnect the 4 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    Text in Illustration 
    *A
    for Double Cab
    *B
    for Single Cab, for Extra Cab


2. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL RH (w/ Power Window)

  1. B277020
    Using a moulding remover, detach the 2 clips.

  1. Disconnect the 4 claws and remove the power window regulator switch assembly with front door armrest base panel.


3. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

  1. B277021E01
    Insert a clip remover between the plate and trim board.

    HINT:
    Tape the clip remover tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Turn the handle counterclockwise to remove the snap ring, front door window regulator handle and plate.


4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  1. B277018E01
    Detach the 2 clips and remove the front door lower frame bracket garnish.
    Text in Illustration 
    *A
    w/o Front No. 2 Speaker
    *B
    w/ Front No. 2 Speaker


5. REMOVE DOOR PULL HANDLE

  1. B277022
    Remove the screw and door pull handle.


6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B277024E01
    for Double Cab:

    1. Remove the clip and screw.

      Text in Illustration 
      *1
      Clip
      *2
      Screw

    2. Detach the 8 clips and remove the front door trim board.

  1. B277023E01
    for Single Cab, for Extra Cab:

    1. Remove the clip and screw.

      Text in Illustration 
      *1
      Clip
      *2
      Screw

    2. Detach the 9 clips and remove the front door trim board.


7. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

B113822
  1. w/ Power Mirror Control System:
    Disconnect the mirror connector.

  1. Remove the 3 nuts.

  1. Push down the claw and remove the outer rear view mirror assembly LH.


8. REMOVE OUTER MIRROR LH

  1. Using a screwdriver, detach the 2 claws as shown in the illustration.

    B278386E01

    Text in Illustration 
    *1
    Screwdriver
    *2
    Protective Tape

    NOTICE:
    Do not pull the outer mirror LH with excessive force. Doing so may cause the actuator to come off or break the mirror surface.

    HINT:
    Apply protective tape to the mirror body and screwdriver tip.

  1. B278387
    Detach the 2 claws at the upper part of the outer mirror.

  1. Remove the outer mirror LH.


9. REMOVE OUTER MIRROR COVER LH (w/ Side Turn Signal Light)

  1. B278447E01
    Remove the tape.
    Text in Illustration 
    *1
    Tape

  1. B278379
    Remove the screw, detach the 5 claws and remove the rubber base.

    HINT:
    It is not necessary to completely remove the rubber base. Slightly move the rubber base so that the outer mirror cover LH can be removed in a later step.

  1. B278380
    Using a T25 "TORX" socket wrench, remove the 3 screws.

  1. B278381
    Using a T25 "TORX" socket wrench, remove the screw.

  1. B278382
    Remove the 3 screws.

  1. Detach the 6 claws.

    B278383E01

  1. Detach the 2 claws and remove the outer mirror cover LH as shown in the illustration.


10. REMOVE OUTER MIRROR COVER LH (w/o Side Turn Signal Light)

B280810
  1. Using a screwdriver, detach the 6 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B280807E01
    Detach the 3 claws as shown in the illustration and remove the outer mirror cover LH.

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →