OPERATION CHECK
Troubleshooting · Vehicles built from Jun 2011
| CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (WINDOW LOCK SWITCH) |
- HINT:
- Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).
- *: for Double Cab
Check that the front passenger side power window and the rear power windows* cannot be operated when the window lock switch of the power window regulator master switch assembly is pressed.

- OK:
- Operation of front passenger side power window and rear power windows* is disabled.
Check that the front passenger side power window and the rear power windows* can be operated when the window lock switch is pressed again.
- OK:
- Front passenger side power window and rear power windows* can be operated.
| CHECK MANUAL UP/DOWN FUNCTION |
- *: for Double Cab
Check that the driver side power window operates as follows:
OK Condition
Power Window Regulator Master Switch Assembly
Switch Operation
Power Window Operation
Ignition switch ON
Driver side
Pulled halfway up
Up (Closes)
Pushed halfway down
Down (Opens)
Check that the front passenger side power window and rear power windows* operate as follows:
OK Condition
Power Window Regulator Switch Assembly
Switch Operation
Power Window Operation
- Ignition switch ON
- Window lock switch off
Front passenger side
Pulled up
Up (Closes)
Pushed down
Down (Opens)
Rear LH side*
Pulled up
Up (Closes)
Pushed down
Down (Opens)
Rear RH side*
Pulled up
Up (Closes)
Pushed down
Down (Opens)
- Ignition switch ON
| CHECK AUTO UP/DOWN FUNCTION |
Check the AUTO light illumination.
After turning the ignition switch ON, check that the AUTO light illuminates (green).
Check that the driver side power window operates as follows:
OK Condition
Power Window Regulator Master Switch Assembly
Switch Operation
Power Window Operation
Ignition switch ON
Driver side
Fully pulled up
Auto up (Fully closes)
Fully pushed down
Auto down (Fully opens)
| CHECK REMOTE MANUAL UP/DOWN FUNCTION |
- *: for Double Cab
Check that the front passenger side power window and rear power windows operate as follows:
OK Condition
Power Window Regulator Master Switch Assembly
Switch Operation
Power Window Operation
- Ignition switch ON
- Window lock switch off
Front passenger side
Pulled up
Up (Closes)
Pushed down
Down (Opens)
Rear LH side*
Pulled up
Up (Closes)
Pushed down
Down (Opens)
Rear RH side*
Pulled up
Up (Closes)
Pushed down
Down (Opens)
- Ignition switch ON
| CHECK PTC OPERATION |
- *1: w/o Regulator
- *2: w/ Regulator
- HINT:
- PTC operation is a function that prevents overloading of the power window regulator by stopping the power window motor. PTC operation activates when the power window regulator switch is operated for a predetermined amount of time.
Disconnect the power window regulator motor assembly*1 or door window regulator sub-assembly*2.
Connect the ammeter's positive (+) lead to terminal 2 of the wire harness side connector and the negative (-) lead to battery's negative terminal.
Connect the battery's positive (+) lead to terminal 1 of the wire harness side connector, and raise that window to the fully closed position.
Continue to apply voltage, and check that the current changes to less than 1A within 4 to 90 seconds.
Disconnect the leads from the terminals.
Approximately 60 seconds later, connect the battery's positive (+) lead to terminal 2 and the negative (-) lead to terminal 1, and check that the window begins to lower.
- NOTICE:
- If the result is not as specified, replace the power window regulator motor assembly*1 or door window regulator sub-assembly*2.
| CHECK JAM PROTECTION FUNCTION (for Driver Side) |
- For vehicles with a jam protection function.
Check the basic function.
- CAUTION:
- The jam protection function is operative during the auto up operation.
- Do not put your fingers between the door frame and door glass to check functions. Also, prevent any part of your body from being caught during inspection.
- The jam protection function is operative during the auto up operation.
- HINT:
- The jam protection function is operative during the auto up operation while the engine is running or the ignition switch is turned to ON.
Fully open the window.
Hold a thick book wrapped with cloth in the position shown in the illustration.

Text in Illustration *1
Thick Book
*2
Cloth
Operate the auto up function to check that the power window goes down when the window contacts the book, and stops when the opening reaches approximately 200 mm (7.87 in.).
- HINT:
- The power window moves down approximately 50 mm (1.97 in.). However, when the opening does not reach 200 mm (7.87 in.), the power window continues to go down until the opening reaches 200 mm (7.87 in.) or until approximately 5 seconds have elapsed.
While the power window is moving down, check that the door glass cannot be moved up even when the power window regulator master switch assembly is used.
| CHECK POWER WINDOW FAIL-SAFE FUNCTION (for Driver Side) |