2014 Hilux · Service Manual ENGINE

P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.
The G signal plate has 5 teeth on its outer circumference and is installed on the pump drive shaft pulley. When the pump drive shaft pulley rotate, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field and generating an electromotive force in the pickup coil.
The NE signal plate has 34 teeth and is mounted on the No. 1 crankshaft position sensor plate. The NE signal sensor generates 34 signals for every engine revolution. The ECM detects the standard crankshaft angle based on the G signal and the actual crankshaft angle and the engine speed by the NE signal.
DTC No.
DTC Detection Condition
Trouble Area
P0340
  1. No camshaft position sensor signal to ECM while cranking
    (2 trip detection logic)
  2. No camshaft position sensor signal to ECM at engine speed of 650 rpm or more
    (1 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Pump drive shaft pulley
  4. ECM
Reference: Inspection using the oscilloscope.
A098437E04
While idling, the correct waveform is shown in the diagram.

HINT:
G stands for the camshaft position sensor signal, and NE stands for the crankshaft position sensor signal.
Item
Content
Terminal
(b) G+ - G-
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Cranking or idling


WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT CAMSHAFT POSITION SENSOR

  1. A064984E26
    Disconnect the C1 camshaft position sensor connector.

  1. Measure the resistance of the camshaft position sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    835 to 1,400 Ω at cold
    1 - 2
    1,060 to 1,645 Ω at hot

    HINT:
    In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensors. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE CAMSHAFT POSITION SENSOR
OK


2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

  1. A099853E12
    Disconnect the C1 camshaft position sensor connector.

  1. Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    C1-1 - G+ (E7-23)
    Below 1 Ω
    C1-2 - G- (E7-31)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    C1-1 or G+ (E7-23) - Body ground
    10 kΩ or higher
    C1-2 or G- (E7-31) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

  1. BR03795E30
    Check the sensor installation.

    OK:
    Sensor is installed correctly.



NG
TIGHTEN SENSOR
OK


4. CHECK PUMP DRIVE SHAFT PULLEY
  1. Check the condition of the pump drive shaft pulley.

    OK:
    Timing sprocket does not have any cracks or deformation.



NG
REPLACE PUMP DRIVE SHAFT PULLEY
OK

REPLACE ECM (Click here)


← P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (Aug 2012 – Jul 2013)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (from Aug 2014) →