P0115 Engine Coolant Temperature Circuit
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Also covers:
- P0117 Engine Coolant Temperature Circuit Low Input
- P0118 Engine Coolant Temperature Circuit High Input
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
A thermistor is built into the Engine Coolant Temperature (ECT) sensor and it changes its resistance value according to the engine coolant temperature.The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0115 |
Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0117 |
Short in ECT sensor circuit for 0.5 seconds (sensor resistance value less than 79 Ω) (1 trip detection logic) |
|
| P0118 |
Open in ECT sensor circuit for 0.5 seconds (sensor resistance value more than 156 kΩ) (1 trip detection logic) |
|
- HINT:
- When DTC P0115, P0117 and/or P0118 is detected, check the engine coolant temperature by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Coolant Temp.
- Reference:
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
| 1. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value.
- OK:
- 75 to 95°C (167 to 203°F) after warming up the engine.
- Result:
Temperature Displayed
Proceed to
-40°C (-40°F)
A
140°C (284°F) or more
B
OK (Same as actual engine coolant temperature)
C
- HINT:
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
- If there is a short circuit, the intelligent tester indicates 140°C (284°F) or more.
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Disconnect the W1 ECT sensor connector.

Connect terminals 1 and 2 of the ECT sensor wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value.
- Standard:
- 140°C (284°F)
|
|
||||
| NG | |
| 3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM) |
Disconnect the W1 ECT sensor connector.

Connect terminals THW and E2 of the E8 ECM connector.
- HINT:
- Before checking, perform a visual and contact pressure check on the ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value.
- Standard:
- 140°C (284°F)
|
|
||||
| NG | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (SHORT IN WIRE HARNESS) |
Disconnect the W1 ECT sensor connector.

Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value.
- Standard:
- -40°C (-40°F)
|
|
||||
| NG | |
| 5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM) |
Disconnect the W1 ECT sensor connector.

Disconnect the E8 ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value.
- Standard:
- -40°C (-40°F)
|
|
||||
| NG | ||
| ||
