P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Also covers:
- P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.
The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.


| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 3 seconds |
Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 3 seconds |
Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic). |
|
- HINT:
- If DTC P0122 and/or P0123 is stored, the following symptoms may appear:
- - Intake booming noise
- - Black smoke
- - Lack of power
- - Vibration at engine stop
- - Turbo overspeed, turbo damage
MONITOR DESCRIPTION
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the throttle position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
T2-1 (VC) - E27-13 (VC)
Always
Below 1 Ω
T2-3 (VTA) - E27-3 (VLU)
Always
Below 1 Ω
T2-2 (E) - E27-14 (E2)
Always
Below 1 Ω
T2-1 (VC) or E27-13 (VC) - Body ground
Always
10 kΩ or higher
T2-3 (VTA) or E27-3 (VLU) - Body ground
Always
10 kΩ or higher
Reconnect the throttle position sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 2. CHECK ECM TERMINAL VOLTAGE (VC TERMINAL) |
Disconnect the throttle position sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
T2-1 (VC) - T2-2 (E)
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Front view of wire harness connector
(to Throttle Position Sensor)
Reconnect the throttle position sensor connector.
|
|
||||
| OK | |
| 3. REPLACE DIESEL THROTTLE BODY ASSEMBLY |
Replace the diesel throttle body assembly (Click here).
| NEXT | |
| 4. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Throttle position.
Check the movement of the throttle valve when idling the engine after starting it from ignition switch to ON.
- OK:
Condition
Tester Display
Ignition switch ON
-5 to 5%
Idling
0 to 93%
|
|
||||
| OK | ||
| ||
| 5. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON for 3 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
