2014 Hilux · Service Manual ENGINE

P0560 System Voltage

Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

While the ignition switch is OFF, battery voltage is supplied to terminal BATT of the ECM for storing DTCs and fuel injection feedback learning values.
DTC No.
DTC Detection Condition
Trouble Area
P0560
Condition (a) or (b) continues:
(a) Significant decrease in battery voltage
(b) Open in back-up power source circuit (1 trip detection logic)
  1. Open in back-up power source circuit
  2. Low battery voltage
  3. ECM

HINT:
If DTC P0560 appears, the ECM does not store other DTCs.


WIRING DIAGRAM

A155388E01

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK FUSE (EFI FUSE)

  1. A099789E10
    Remove the EFI fuse from the engine room junction block.

  1. Measure the resistance of the EFI fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2. CHECK ECM (BATT VOLTAGE)

  1. A154534E06
    Measure the voltage of the E7 and E6 ECM connectors.

    Standard voltage:
    Tester Connection
    Specified condition
    E6-2 (BATT) - E7-7 (E1)
    11 to 14 V



NG
Go to step 3
OK

REPLACE ECM

3. CHECK HARNESS AND CONNECTOR (ECM - EFI FUSE, EFI FUSE - BATTERY)

  1. A154739E01
    Check the harness and the connector between the EFI fuse and ECM.
    1. Disconnect the E6 ECM connector.

    2. Remove the EFI fuse from the engine room junction block.

    3. Measure the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      E6-2 (BATT) - 2 (EFI fuse)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      E6-2 (BATT) or 2 (EFI fuse) - Body ground
      10 kΩ or higher

  1. Check the harness and the connector between the EFI fuse and battery.

    1. Remove the EFI fuse from the engine room junction block.

    2. Disconnect the positive battery terminal.

    3. Measure the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      Battery positive terminal - EFI fuse (1)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      Battery positive terminal or EFI fuse (1) - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted



NG
REPLACE BATTERY
OK

CHECK AND REPLACE ENGINE ROOM JUNCTION BLOCK


← P0560 System Voltage (Jun 2011 – Jul 2012)P0560 System Voltage (Aug 2013 – Jul 2014) →