2014 Hilux · Service Manual ENGINE

P007C Charge Air Cooler Temperature Sensor Circuit Low

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

A208462E01
The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.
P007C 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
  1. Short in intake air temperature sensor (turbo) circuit
  2. Intake air temperature sensor (turbo)
  3. ECM
P007D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
  1. Open in intake air temperature sensor (turbo) circuit
  2. Intake air temperature sensor (turbo)
  3. ECM
Related Data List 
DTC No.
Data List
P007C
Intake Air Temp (Turbo)
P007D

HINT:
  1. If DTC P007C or P007D is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. White smoke
    5. Lack of power


WIRING DIAGRAM

A258706E01

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE (TURBO))
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    OK:
    Same as air temperature near intake manifold

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    OK (same as air temperature near intake manifold)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or higher.



B
Go to step 4

C
Go to step 11
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A204915E11
    Disconnect the intake air temperature sensor (turbo) connector.

  1. Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    Intake Air Temperature Sensor (Turbo)
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Intake Air Temperature Sensor (Turbo))

  1. Reconnect the intake air temperature sensor (turbo) connector.



OK
Go to step 7

NG
Go to step 3
3. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
  1. Disconnect the intake air temperature sensor (turbo) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I4-2 - E26-3 (THIA)
    Always
    Below 1 Ω
    I4-1 - E27-14 (E2)
    Always
    Below 1 Ω

  1. Reconnect the intake air temperature sensor (turbo) connector.

  1. Reconnect the ECM connector.



OK
Go to step 9

NG
Go to step 8
4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A198733E22
    Disconnect the intake air temperature sensor (turbo) connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Intake Air Temperature Sensor (Turbo)
    *2
    ECM

  1. Reconnect the intake air temperature sensor (turbo) connector.



OK
Go to step 10

NG
Go to step 5
5. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
  1. Disconnect the intake air temperature sensor (turbo) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I4-2 or E26-3 (THIA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the intake air temperature sensor (turbo) connector.

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
7. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO).
  1. Replace the intake air temperature sensor (turbo) (Click here).



NEXT
Go to step 11
8. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 11
9. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.
  1. Replace the ECM (Click here).



NEXT
Go to step 11
10. REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
  1. Replace the intake air temperature sensor (turbo) (Click here).


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0069 MAP Sensor Too High or Too Low (from Aug 2014)P007C Charge Air Cooler Temperature Sensor Circuit Low (+ P007D) (Aug 2012 – Jul 2013) →