P007C Charge Air Cooler Temperature Sensor Circuit Low
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- P007D Charge Air Cooler Temperature Sensor Circuit High
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION


The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 1 second |
Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 1 second |
Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC No. |
Data List |
| P007C |
Intake Air Temp (Turbo) |
| P007D |
- HINT:
- If DTC P007C or P007D is stored, the following symptoms may appear:
- Misfire
- Combustion noise
- Black smoke
- White smoke
- Lack of power
- If DTC P007C or P007D is stored, the following symptoms may appear:
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE (TURBO)) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
- OK:
- Same as air temperature near intake manifold
Result Result
Proceed to
-40°C (-40°F)
A
140°C (284°F) or higher
B
OK (same as air temperature near intake manifold)
C
- HINT:
- If there is an open circuit, the tester indicates -40°C (-40°F).
- If there is a short circuit, the tester indicates 140°C (284°F) or higher.
- If there is an open circuit, the tester indicates -40°C (-40°F).
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Disconnect the intake air temperature sensor (turbo) connector.

Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
- OK:
- 140°C (284°F) or higher
Text in Illustration *1
Intake Air Temperature Sensor (Turbo)
*2
ECM
*a
Front view of wire harness connector
(to Intake Air Temperature Sensor (Turbo))
Reconnect the intake air temperature sensor (turbo) connector.
|
|
||||
|
|
||||
| 3. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM) |
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I4-2 - E26-3 (THIA)
Always
Below 1 Ω
I4-1 - E27-14 (E2)
Always
Below 1 Ω
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
|
|
||||
|
|
||||
| 4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
Disconnect the intake air temperature sensor (turbo) connector.

Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
- OK:
- -40°C (-40°F)
Text in Illustration *1
Intake Air Temperature Sensor (Turbo)
*2
ECM
Reconnect the intake air temperature sensor (turbo) connector.
|
|
||||
|
|
||||
| 5. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM) |
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I4-2 or E26-3 (THIA) - Body ground
Always
10 kΩ or higher
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 6. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 7. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO). |
Replace the intake air temperature sensor (turbo) (Click here).
|
|
||||
| 8. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
|
||||
| 9. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM. |
Replace the ECM (Click here).
|
|
||||
| 10. REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO) |
Replace the intake air temperature sensor (turbo) (Click here).
| NEXT | |
| 11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
