P0095 Intake Air Temperature Sensor 2 Circuit
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Also covers:
- P0097 Intake Air Temperature Sensor 2 Circuit Low
- P0098 Intake Air Temperature Sensor 2 Circuit High
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The Intake Air Temperature (IAT) sensor is built into the inter cooler and senses the IAT. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (see Fig. 1).The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0095 |
Open or short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0097 |
Short in intake air temperature sensor circuit for 0.5 seconds (sensor resistance value less than 25 Ω [sensor output voltage less than 0.05 V]) (1 trip detection logic) |
|
| P0098 |
Open in intake air temperature sensor circuit for 0.5 seconds (sensor resistance value more than 156 kΩ [sensor output voltage more than 4.9 V]) (1 trip detection logic) |
|
- HINT:
- When DTC P0095, P0097 and/or P0098 is set, check the intake air temperature by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Intake Air Temp (Turbo).
- Reference:
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
| 1. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMP [TURBO]) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).
Read the value.
- OK:
- Same value as the actual intake air temperature.
- Result:
Temperature Displayed
Proceed to
-40°C (-40°F)
A
140°C (284°F) or more
B
OK (same as air temperature near to intake manifold)
C
- HINT:
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
- If there is a short circuit, the intelligent tester indicates 140°C (284°F) or more.
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Disconnect the I4 intake air temperature sensor connector.

Connect terminals 1 and 2 of the intake air temperature sensor wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).
Read the value.
- Standard:
- 140°C (284°F)
|
|
||||
| NG | |
| 3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM) |
Disconnect the I4 intake air temperature sensor connector.

Connect terminals THIA and E2 of the E8 ECM connector.
- HINT:
- Before checking, perform a visual and contact pressure check on the ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).
Read the value.
- Standard:
- 140°C (284°F)
|
|
||||
| NG | ||
| ||
| 4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
Disconnect the I4 intake air temperature sensor connector.

Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).
Read the value.
- Standard:
- -40°C (-40°F)
|
|
||||
| NG | |
| 5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM) |
Disconnect the I4 intake air temperature sensor connector.

Disconnect the E8 ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).
Read the value.
- Standard:
- -40°C (-40°F)
|
|
||||
| NG | ||
| ||
