P2454 Diesel Particulate Filter Pressure Sensor "A" Circuit Low
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Also covers:
- P2455 Diesel Particulate Filter Pressure Sensor "A" Circuit High
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- HINT:
- For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures (Click here).
- If P2454 and/or P2455 is present, refer to the DTC chart for DPF system (Click here).
- For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures (Click here).


The two sensing chambers of the differential pressure sensor assembly are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.
The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor assembly. If the difference in pressure exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.
When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P2454 or P2455, and illuminates the MIL.
- HINT:
- If the vacuum hoses of the differential pressure sensor assembly are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance) is stored and the MIL illuminates.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 5 seconds |
differential pressure sensor assembly output voltage is below 0.4 V for 3 seconds or more. (1 trip detection logic) |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 5 seconds |
differential pressure sensor assembly output voltage is higher than 4.8 V for 3 seconds or more. (1 trip detection logic) |
|
| DTC No. |
Data List |
| P2454 |
DPF Differential Pressure |
| P2455 |
- HINT:
- DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range / Performance) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor assembly.
- After confirming DTC P2454 and P2455, check the differential pressure in the "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" menu using the intelligent tester.
- DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range / Performance) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor assembly.
Reference: Condition
Differential Pressure Output
Sensor Condition
Ignition switch ON
Approximately 0 kPa
Normal
Always
-5 kPa or less or higher than 99 kPa
Open or short circuit
4000 rpm (No engine load)
Negative output
Incorrect hose routing
MONITOR DESCRIPTION
In order to detect abnormality in the differential pressure sensor assembly, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK WIRE HARNESS (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM) |
Disconnect the differential pressure sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D19-2 (PEX) - E27-7 (PEX)
Always
Below 1 Ω
D19-3 (VC) - E27-13 (VC)
Always
Below 1 Ω
D19-1 (E2) - E27-14 (E2)
Always
Below 1 Ω
D19-2 (PEX) or E27-7 (PEX) - Body ground
Always
10 kΩ or higher
D19-3 (VC) or E27-13 (VC) - Body ground
Always
10 kΩ or higher
Reconnect the differential pressure sensor assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 2. CHECK TERMINAL VOLTAGE (VC) |
Disconnect the differential pressure sensor assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D19-3 (VC) - Body ground
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Front view of wire harness connector
(to Differential Pressure Sensor Assembly)
Reconnect the differential pressure sensor assembly connector.
|
|
||||
| OK | |
| 3. REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY |
Replace the differential pressure sensor assembly (Click here).
|
|
||||
| 4. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 5. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON and wait for 5 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
