2014 Hilux · Service Manual ENGINE

P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.

The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.
G036462E06
DTC No.
DTC Detection Condition
(All of following are 1 trip detection logic)
Trouble Area
P2120
Condition (a) continues for 0.5 sec. or more:
(a) VPA is 0.4 V or less
(b) VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Accelerator pedal
  3. Accelerator pedal rod (arm) deformed
  4. ECM
P2122
VPA is 0.4 V or less for 0.5 sec. or more when VPA2 output indicate accelerator pedal is opened
  1. Accelerator pedal position sensor
  2. Open in VCPA circuit
  3. VPA circuit open or ground short
  4. Accelerator pedal
  5. Accelerator pedal rod (arm) deformed
  6. ECM
P2123
Condition (a) continues for 2.0 sec. or more:
(a) VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Open in EPA circuit
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM
P2125
Condition (a) or (b) continues for 0.5 sec. or more:
(a) VPA2 is 1.2 V or less
(b) VPA2 is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Accelerator pedal
  3. Accelerator pedal rod (arm) deformed
  4. ECM
P2127
VPA2 is 1.2 V or less for 0.5 sec. or more when VPA output indicates accelerator pedal is opened
  1. Accelerator pedal position sensor
  2. Open in VCP2 circuit
  3. VPA2 circuit open or ground short
  4. Accelerator pedal
  5. Accelerator pedal rod (arm) deformed
  6. ECM
P2128
Conditions (a) and (b) continue for 2.0 sec. or more:
(a) VPA2 is 4.8 V or more
(b) VPA is 0.4 V or more and VPA is 3.45 V or less
  1. Accelerator pedal position sensor
  2. Open in EPA2 circuit
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM
P2138
Condition (a) or (b) continues for 2.0 sec. or more:
(a) Difference between VPA and VPA2 is 0.02 V or less
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less
  1. VPA and VPA2 circuits are short circuited
  2. Accelerator pedal position sensor
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM

WIRING DIAGRAM

A133490E05

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ACCEL SENS. NO.1 VOLT % AND ACCEL SENS. NO.2 VOLT %)

  1. FI07052E07
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

  1. Read the values.

    Standard:
    Accelerator Pedal
    Accel Sens. No.1 Volt %
    Accel Sens. No.2 Volt %
    Released
    10 to 22%
    24 to 40%
    Depressed
    52 to 90%
    68 to 99%



OK
Go to step 5
NG


2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A099833E09
    Disconnect the A13 sensor connector.

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VCP2 (A13-1) - VCP2 (E5-27)
    Below 1 Ω
    EPA2 (A13-2) - EPA2 (E5-29)
    Below 1 Ω
    VPA2 (A13-3) - VPA2 (E5-23)
    Below 1 Ω
    VCPA (A13-4) - VCPA (E5-26)
    Below 1 Ω
    EPA (A13-5) - EPA (E5-28)
    Below 1 Ω
    VPA (A13-6) - VPA (E5-22)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VCP2 (A13-1) or VCP2 (E5-27) - Body ground
    10 kΩ or higher
    EPA2 (A13-2) or EPA2 (E5-29) - Body ground
    10 kΩ or higher
    VPA2 (A13-3) or VPA2 (E5-23) - Body ground
    10 kΩ or higher
    VCPA (A13-4) or VCPA (E5-26) - Body ground
    10 kΩ or higher
    EPA (A13-5) or EPA (E5-28) - Body ground
    10 kΩ or higher
    VPA (A13-6) or VPA (E5-22) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VCPA AND VCP2 VOLTAGE)

  1. A096639E12
    Disconnect the A13 sensor APP connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VCPA (E5-26) - EPA (E5-28)
    4.5 to 5.5 V
    VCP2 (E5-27) - EPA2 (E5-29)



NG
REPLACE ECM (Click here)
OK


4. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace accelerator pedal rod assembly (Click here).


NEXT


5. CHECK IF OUTPUT DTC RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTC.

    Result:
    Display (DTC output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127, P2128, or P2138 is output again
    A
    No output
    B



B
END
A

REPLACE ECM (Click here)


← P2009 Intake Manifold Runner Control Circuit Low (Bank 1) (+ P2010) (from Aug 2014)P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (Aug 2012 – Jul 2013) →